448559
5
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
ENGLISH
Explanation of general view
1 Blade
2 Push button
3 Hex wrench 4
4 Loosen
5 Tighten
6 Pin
7 Screw
8 Slider
9 Blade clamp
10 Hole
11 Lever
12 Shoe
13 Switch trigger
14 Lock button/Lock-off button
15 Limit mark
16 Screwdriver
17 Brush holder cap
SPECIFICATIONS
Model JR3030 JR3030T
Length of stroke .......................................................... 28 mm 28 mm
Strokes per minute ..................................................... 0 2,600 0 2,600
Cutting capacities
Pipe .......................................................................... 90 mm 90 mm
Wood ........................................................................ 90 mm 90 mm
Overall length ............................................................. 438 mm 460 mm
Net weight ................................................................... 3.5 kg 3.5 kg
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
ADDITIONAL SAFETY RULES
1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear pro-
tectors and thickly padded gloves.
2. Check the blade carefully for cracks or dam-
age before operation. Replace cracked or
damaged blade immediately.
3. Do not attempt to cut workpieces larger than
specified in this manual (especially hollow
pipe). The blade might snap and cause an
injury. (Fig. 1)
4. Hold the tool firmly.
5. Be sure no one is below when using the tool in
high locations.
6. Do not point the tool at anyone in the immedi-
ate vicinity.
7. When making a ‘‘blind’ cut (you can’t see
behind what is being cut), be sure that hidden
electrical wiring or water pipes are not in the
path of the cut. If wires are present, they must
be disconnected at their power source by a
qualified person or avoided to prevent the
possibility of lethal shock or fire. Always hold
the tool ONLY by the insulated gripping sur-
faces to prevent any electric shock if you
accidentally cut through a ‘live’’ wire. Water
pipes in ‘blind’’ areas must be drained and
capped before cutting.
8. Be careful not to hit the end of the blade
against something during operation. Damage
to the tool or dangerous blade breakage may
occur. (Fig. 2)
9. Watch out for cut-off portions of the workpiece
being cut. They may fall and injure you or
someone near you.
10. When cutting metals, be cautious of hot flying
chips.
11. Do not touch the blade or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
12. If you withdraw the blade from the workpiece
during operation, strong reaction will be pro-
duced, causing the blade to snap or causing
you to lose your grip and control of the tool.
Always switch off the tool and wait until the
blade has come to a complete stop before
withdrawing the blade from the workpiece.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing saw blade
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the blade.
Always clean out all chips or foreign matter adher-
ing to the blade, blade clamp and/or slider. Failure
to do so may cause insufficient tightening of the
blade, resulting in a serious injury.
JR3030 (E) (’101. 1. 9)
5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita JR 3030 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita JR 3030 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita JR 3030

Makita JR 3030 Gebruiksaanwijzing - Nederlands, English - 7 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info