Handleiding Makita HM0870C (pagina 6 van 44) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

448476

Verklein

Vergroot

Pagina terug

1/44

Pagina verder

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the tool is switched off.

• Switch can be locked in “ON” position for ease of

operator comfort during extended use. Apply caution

when locking tool in “ON” position and maintain firm

grasp on tool.

To start the tool, push the switch lever “ON (I)” on the left

side of the tool. To stop the tool, push the switch lever

“OFF (O)” on the right side of the tool.

Speed change (Fig. 2)

The blows per minute can be adjusted just by turning the

adjusting dial. This can be done even while the tool is

running. The dial is marked 1 (lowest speed) to 5 (full

speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the blows per

minute.

CAUTION:

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

For Model HM0871C only

NOTE:

• Blows at no load per minute becomes smaller than

those on load in order to reduce vibration under no

load, but this does not show trouble. Once operation

starts with a bit against concrete, blows per minute

increase and get to the numbers as shown in the table.

When temperature is low and there is less fluidity in

grease, the tool may not have this function even with

the motor rotating.

Indicator lamp (Fig. 3)

The green power-ON indicator lamp lights up when the

tool is plugged. If the indicator lamp does not light up, the

mains cord or the controller may be malfunction. The

indicator lamp is lit but the tool does not start even if the

tool is switched on, the carbon brushes may be worn out,

or the controller, the motor or the ON/OFF switch may be

malfunction.

The red service indicator lamp flickers up when the

carbon brushes are nearly worn out to indicate that the

tool needs servicing. After approx. 8 hours of use, the

motor will automatically be shut off.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side handle (auxiliary handle)

For tool with stick type side handle (Fig. 4)

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip

by turning it counterclockwise, swing it to the desired

position and then tighten it by turning clockwise.

For tool with D-shaped side handle (Fig. 5)

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal. Just

loosen the clamp nut to swing the side handle to a desired

position. Then tighten the clamp nut securely.

Installing or removing the bit (Fig. 6)

Clean the bit shank and apply bit grease before installing

the bit.

Insert the bit into the tool. Turn the bit and push it in until it

engages. (Fig. 7)

If the bit cannot be pushed in, remove the bit. Pull the

releasing cover down a couple of times. Then insert the

bit again. Turn the bit and push it in until it engages.

(Fig. 8)

After installing, always make sure that the bit is securely

held in place by trying to pull it out. (Fig. 9)

To remove the bit, pull the releasing cover down all the

way and pull the bit out.

Bit angle (Fig. 10 & 11)

The bit can be secured at 12 different angles. To change

the bit angle, slide the change ring forward, then turn the

change ring to change the bit angle. At the desired angle,

slide the change ring back to the original position. The bit

will be secured in place.

NOTE:

• The change ring cannot turn when the bit is not

installed on the tool.

OPERATION

Chipping/Scaling/Demolition (Fig. 12 &

13)

Always use the side grip (auxiliary handle) and firmly hold

the tool by both side grip and switch handle during

operations. Turn the tool on and apply slight pressure on

the tool so that the tool will not bounce around,

uncontrolled. Pressing very hard on the tool will not

increase the efficiency.

Number on adjusting dial Blows per minute

5 2,650

4 2,400

3 1,750

2 1,300

1 1,100

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita HM0870C Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info