448481
5
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
ENGLISH
Explanation of general view
1 Bit grease
2 Bit shank
3 Tool holder cap
4 Tool holder cover
5 Cut in bit shank
6 Notch in tool holder cap
7 Change ring
8 Side handle
9 Can be swung 360° on the
vertical and secured at any
desired position
0 Secures at eight different
positions back and forth
on the horizontal
q Clamp nut
w Loosen
e Tighten
r ‘‘ON I’’ button
t ON
y OFF
u Adjusting dial
i Screwdriver
o Rear cover
p Screws
a Brush holder cap
s Socket wrench
d Crank cap
f Hammer grease
SPECIFICATIONS
Model HM1140C
Blows per minute ............................... 1,300 2,650
Overall length ............................................. 517 mm
Net weight ...................................................... 6.3 kg
Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear pro-
tectors and thickly padded gloves.
2. Be sure the bit is secured in place before
operation.
3. Under normal operation, the machine is
designed to produce vibration. The screws
can come loose easily, causing a breakdown
or accident. Check tightness of screws care-
fully before operation.
4. In cold weather or when the machine has not
been used for a long time, let the machine
warm up for several minutes by operating it
under no load. This will loosen up the lubrica-
tion. Without proper warm-up, hammering
operation is difficult.
5. Always be sure you have a firm footing.
Be sure no one is below when using the
machine in high locations.
6. Hold the machine firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the machine running. Operate the
machine only when hand-held.
9. Do not point the machine at any one in the
area when operating. The bit could fly out and
injure someone seriously.
10. When chipping into walls, floors or wherever
“live” electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE!
Hold the machine by the insulated grasping
surfaces to prevent electric shock if you chip
into a “live” wire.
11. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing bit
Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the bit.
This machine accepts 3/4 Hexagonal and 21/32
round shank bits. Clean the bit shank and apply the bit
grease provided to it before installing the bit. (Fig. 1)
Pull the tool holder cover down all the way. (Fig. 2-1)
With the cut in the bit shank aligned with the notch in
the tool holder cap, insert the bit into the tool holder.
(Fig. 2-2)
Release the tool holder cover. It will return automati-
cally to its original position to secure the bit. (Fig. 2-3)
After installing, always make sure that the bit is
securely held in place by trying to pull it out.
To remove the bit, pull the tool holder cover down all
the way and pull the bit out.
Bit angle (Fig. 3)
The bit can be secured at 12 different angles. To
change the bit angle, slide the change ring forward,
then turn the change ring to change the bit angle. At
the desired angle, slide the change ring back to the
original position. Then turn the change ring slightly so
that the bit will be secured in place with a little click.
HM1140C (E) (’98. 9. 7)
5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita HM 1140C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita HM 1140C in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita HM 1140C

Makita HM 1140C Gebruiksaanwijzing - Nederlands, English - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info