79160
23
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
23
2 3
6
7
8
45
12
10
9
11
12
1
Replacing the spark plug
CAUTION:
Do not touch the spark plug or plug cap if the engine is
running (high voltage).
Switch off the engine before starting any maintenance work.
A hot engine can cause burns. Wear protective gloves!
The spark plug must be replaced in case of damage to the
insulator, electrode erosion (burn) or if the electrodes are very
dirty or oily.
Pull the plug cap (1) off the spark plug. Use only the combination
wrench supplied with the saw to remove the spark plug.
CAUTION: Use only the following spark plugs: NGK BPMR 7A.
Electrode gap
The electrode gap must be 0.5 mm.
A
0,5 mm
Replacing the starter cable
Unscrew four screws (2). Remove fan housing (3).
Remove all pieces of cable.
Unscrew screw (4). Hold the cable drum (7) rmly and remove
the drive spindle (5) and spring (6).
CAUTION: Danger of injury! The return spring unit (9) is
not secured and can fall out of the fan housing. The return
spring is under tension and pop out of the unit! If this hap-
pens, the spring can be replaced in the unit as shown in the
illustration (note the direction of rotation!).
Secure the return spring unit (9) against falling out and care-
fully take off the cable drum (7).
Thread a new cable (dia. 3 mm, length 900 mm), as shown in the
illustration (note the stop (11)) and tie a knot in both ends.
Pull the knots (12) into the cable drum (7) and starter handle (10).
Put the cord drum back on and turn gently until the return spring
catches.
Install the drive spindle (5) and spring (6), screw in the screw
(4) and tighten.
Guide the cable into the space (8) on the drum and use the
cable to turn the drum two turns clockwise.
Hold the cable drum with your left hand and with your right hand
untwist the cable, pull it tight and hold it.
Carefully release the cable drum. The spring will wind the cable
around the drum.
Repeat three or four times. The starter grip should now be held
upright on the fan housing.
CAUTION: Danger of injury! Secure the cable grip when
pulled out! It will whip back if the cable pulley is released
by accident.
NOTE: With the cable pulled all the way out, it must still be
possible to turn the pulley another 1/4 turn against the return
spring.
When replaceing fan housing, it may be necessary to pull the
starter cable lightly so that the cable pulley catches.
B
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DCS 3410 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DCS 3410 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita DCS 3410

Makita DCS 3410 Gebruiksaanwijzing - Deutsch, Italiano - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info