581654
6
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
6
Dear MAGNAT Customer,
Congratulations on your fine new loudspeakers and thank you very much for choosing MAGNAT! You have made an
excellent choice. The high-quality speakers produced by MAGNAT are renowned all over the world.
Please study the instructions and information below carefully before using your new loudspeakers.
SET-UP INFORMATION
QUANTUM SIGNATURE should if possible be set up without obstruction and slightly inclined towards the place of listening
(fig. 1).
In the ideal configuration the speakers and the listening position should form an equilateral triangle. When the left and right
speakers are the same distance from the listening position their sound arrives at the same time, resulting in a harmonious,
natural music reproduction.
There should be a clear line of sight between the loudspeakers and the listening position. Any sound-absorbing or reflecting
obstacles in the path will distort the sound.
GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT QUANTUM SIGNATURE LOUDSPEAKERS
Warning: Only hi-fi amplifier loudspeaker outputs may be connected to the QUANTUM SIGNATURE loudspeaker
terminal.
Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment of sound
quality, we recommend cables with cross-sections of at least 2.5 mm² for lengths up to 3 m and at least 4 mm² for lengths
above 3 m.
Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. Place the loudspeakers
in their planned positions and cut the cables to the right length. The cables for both channels should always be exactly the
same length.
For good sound it is imperative that the cables must be connected in such a way that the speakers are “in phase”. This
means that the black negative terminals on the speakers (-) must be connected to the negative (-) terminals on the amplifier,
the red positive (+) speaker terminals to the positive (+) amplifier terminals. To make this easier one wire of most speaker
cables is marked with a coloured strip or a ridge in the insulation.
The QUANTUM SIGNATURE terminal is designed for 3 cord sets:
a) Connection via banana plugs
b) Connection via clevis type fittings
c) Non-ready-made:
Strip 10 – 15 mm of insulation from the ends of non-ready-made cables. Twist the ends – this is much better than tinning
them with solder – insert them in the terminals and tighten the terminal screws firmly.
Before switching on the system double-check all your connections and make sure that the terminal screws are tight and that
there are no short circuits caused by stray wire filaments – this could cause serious damage to your amplifier!
SPIKES
You should use the supplied spikes. The spikes are height-adjustable and possess a counter nut.
Any irregularities in the floor may be offset and a firm stand may be achieved with the spikes. They also decouple the
loudspeakers from the base so that any undesirable resonance is avoided.
The spikes must be screwed into the threaded sleeves at the bottom of the box. In order to prevent the floor from being
damaged, you should get help from someone to tilt the box slightly when fitting the spikes.
First, screw in two spikes next to each other and – before setting the box down – put the corresponding washers (rubber
facing down) in place. Then attach the two opposite spikes and lower accordingly. Then align the box vertically and counter
the spikes.
MAGNAT QUANTUM SIGNATURE - BI-WIRING AND BI-AMPING
Bi-wiring means using separate cables to carry the high and low audio frequencies. Bi-amping takes this idea one step
further and uses separate power amplifiers as well as separate cables for high and low frequencies. Bi-amping in particular
produces an additional improvement in sound reproduction quality.
The special connection terminals of the QUANTUM SIGNATURE loudspeakers support both conventional connection and
operation in bi-wiring and bi-amping modes. There are four screw terminals on each speaker. The top pair are for the tweeter
(high frequencies), the lower pair for the woofer (low frequencies). The factory-installed cables strips connecting the positive
and negative terminals are for conventional 2-wire connection and must be removed for bi-wiring and bi-amping operation.
The pictures below show the correct set-up for conventional operation (fig. 2a), bi-wiring (fig. 2b) and bi-amping (fig. 2c).
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Magnat Quantum Signature bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Magnat Quantum Signature in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info