629101
16
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
Operating Manual English
13
Connect the black jump lead first
to the negative terminal (–) of the
donor battery. Connect the other
clip to the frame of the engine
block of the tractor with the flat
battery (as far away from the
battery as possible).
Note
If the donor battery is installed in a
vehicle, this vehicle must not be
started during the jump starting
process.
Start the tractor with the flat
battery and actuate the parking
brake.
Disconnect the jump leads in
reverse sequence.
Tyre pressure
Warning
Never exceed the maximum
permitted tyre pressure (see tyre
wall). When pumping up the tyres,
do not stand in front of or over the
tyre.
Excessive tyre pressure reduces
the service life of the tyres. Always
check the tyre pressure before
driving.
After 5 operating hours
First engine oil change. See
engine manual for subsequent
intervals.
Use the oil channel or (optional)
quick oil drain (Fig. 16).
After 10 operating hours
Lubricate all rotating and bearing
points of the accelerator pedal
and brake pedal with several
drops of light oil.
Clean battery poles and
terminals.
Every 25 operating hours
Lubricate all blade shafts,
tensioning pulleys and
tensioning pulley holders via the
grease nipples using grease type
251H EP. Have this work carried
out by a service centre.
Lubricate the wheel bearings and
front wheel axes with 251H EP
type grease applied to their
respective grease nipples.
Remove grass and dirt around
the blade shafts beneath the
covers. Have this work carried
out by a service centre.
Lubricate the steering with
grease Type 251H EP via the
grease nipples on the steering
support. Have this work carried
out by a service centre.
Every 50 operating hours
Have dirt and grass remnants
removed from the drive gear by
a repair shop.
If required
Charge the battery
If you are not using the unit for
a prolonged period, it is recommen-
ded to take the battery out of the
unit and charge it before storage,
as well as every 2 months during
storage, and before starting up the
unit again.
Check the battery’s charged state
with a voltmeter. When the charged
state is less than 12.6 V (DC)
recharge the battery (max 12 V
at 6 A) with a battery charger in
accordance with the table.
Note
Follow the instructions in the
operating manual for your battery
charger.
Replacing fuses
Replace defective fuses only with
fuses of the same amperage.
Hydraulic expansion vessel
Fig. 17
Is used as an expansion vessel for
the hydraulic fluid during operation.
Maintenance and inspection only
by a specialist company during
annual maintenance.
Notes
Do not check until the hydraulic
oil has completely cooled down.
The oil level should be at least
between the base of the tank and
the mark (1).
Once per season
Lubricate all rotating and bearing
points (operating lever, height
adjustment of the cutter deck ...)
with several drops of light oil.
Clean the spark plug and check
the gap between the electrodes
or replace the plug. See engine
handbook.
The rear axles must be lubricated
with a special-purpose (water-
repellent) grease at a specialised
garage.
Have the cutting blade
sharpened or replaced in
a specialist workshop.
Note
Regularly check (when visiting your
workshop) the condition of the
mower deck V-belt.
Removing/Installing and
adjusting cutter deck
Danger
Injury hazard if engine is started
inadvertently
Protect yourself against injury.
Before carrying out any work on the
mower
park the appliance on a level
surface,
switch off the engine,
withdraw the ignition key,
switch off PTO,
lock the parking brake.
wait until all moving parts have
come to rest and the engine has
fully cooled,
remove the spark plug connector
on the engine in order to prevent
the engine from accidentally
being started.
Danger
Injury hazard due to sharp cutting
blade.
Wear protective gloves.
Disassembly
Warning
The hanger/lifting mechanism is
spring-loaded and may spring
upwards as soon as the cutterdeck
is disconnected from the lifting
mechanism – work cautiously.
Voltmeter Battery
charging state
Charging
time
12.7 volts 100 %
12.4 volts 75 %
approx.
90 min.
12.2 volts 50 %
approx.
180 min.
12.0 volts 25 %
approx.
280 min.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD Zero Turn Serie Z-Force SZ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD Zero Turn Serie Z-Force SZ in de taal/talen: Engels als bijlage per email.

De handleiding is 8,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van MTD Zero Turn Serie Z-Force SZ

MTD Zero Turn Serie Z-Force SZ Gebruiksaanwijzing - Deutsch - 19 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info