629100
16
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
Operating Manual English
13
Note
Follow the instructions in the
operating manual for your battery
charger.
Replacing fuses
Replace defective fuses only with
ones of an equal strength.
Once per season
Lubricate all rotating and bearing
points (operating lever, height
adjustment of the cutter deck ...)
with several drops of light oil.
Clean the spark plug and check
the gap between the electrodes
or replace the plug. See engine
handbook.
The rear axles must be lubricated
with a special-purpose (water-
repellent) grease at a specialised
garage.
Have the cutting blade
sharpened or replaced in
a specialist workshop.
Note
Regularly check (when visiting your
workshop) the condition of the
mower deck V-belt.
Removing/Installing and
adjusting cutter deck
Danger
Injury hazard if engine is started
inadvertently
Protect yourself against injury.
Before carrying out any work on the
mower
park the appliance on a level
surface,
switch off the engine,
withdraw the ignition key,
switch off PTO,
lock the parking brake.
wait until all moving parts have
come to rest and the engine has
fully cooled,
remove the spark plug connector
on the engine in order to prevent
the engine from accidentally
being started.
Danger
Injury hazard due to sharp cutting
blade.
Wear protective gloves.
Disassembly
Raise cutter deck into a position
in which the V-belt is as
horizontal as possible between
the cutter deck and PTO clutch.
Remove the V belt (1) from the
PTO clutch/motor pulley (2) –
fig. 20.
To do this, pull left or right side of
the V-belt backwards and then
downwards while manually
turning the engine belt pulley in
the opposite direction.
Note:
Work carefully to avoid
trapping your fingers.
Move cutting height adjustment
lever to the lowest position.
Remove front fixing bracket from
the cutter deck – Fig. 19. Pull
cotter pin (1) and pull the fixing
bracket (2) out of the holder.
Note:
In doing so, support the
cutters firmly so that they cannot
simply drop to the ground.
Pull out the pin (1) on the left and
right of the cutter deck to
disconnect the cutter deck from
the hanger (2) – Fig. 13.
Note:
In doing so, support the
cutters firmly so that they cannot
simply drop to the ground.
Move cutting height adjustment
lever to the highest position.
Pull out the cutters from beneath
the appliance.
Assembly
To reinstall the cutters perform the
above steps (for removing the
cutters) in reverse order. Work
proceeds faster when you are
assisted by a second person. Make
sure that the suspension units are
in their respective recesses on the
cutter mount and the pin has
engaged correctly.
Note
Following assembly, check that the
V-belt is positioned correctly and is
not twisted – Figs. 21 to 23.
Setting the cutter level
When mowing does not appear to
be parallel to the lawn the cutters
can be aligned.
Note
Before aligning the cutters check
the tyre pressure on the appliance.
Setting the side level
Fig. 11
Raise the cutters to the top.
Carefully turn the outer cutters
(risk of injury) transverse to the
drive direction.
Measure the distance between
the ground and the ends of the
two outer cutters. The result
should be the same. If required,
set the correct level by rotating
the setting segment (2) on the left
cutter deck side. To do so first
loosen (but do not remove) the
cap bolt (1) and retighten this
after the adjustment.
Set the level from front to back.
Fig. 10
Note
Set/check the side level before this
adjustment.
Raise the cutters to the top.
Carefully turn the outer cutters
(risk of injury) parallel to the drive
direction.
Measure the distance between
the ground and the end of the
right cutter. The end of the front
cutter should be about 3.2–6 mm
lower than the end of the rear
cutter. You may have to adjust
the front receiver (1). To do this,
set the correct level by adjusting
the nut (2).
Voltmeter Battery
charging
state
Charging
time
12.7 volts 100 %
12.4 volts 75 % approx.
90 min.
12.2 volts 50 % approx.
180 min.
12.0 volts 25 % approx.
280 min.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD Zero Turn Serie RZT-S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD Zero Turn Serie RZT-S in de taal/talen: Engels als bijlage per email.

De handleiding is 6,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van MTD Zero Turn Serie RZT-S

MTD Zero Turn Serie RZT-S Gebruiksaanwijzing - Nederlands - 19 pagina's

MTD Zero Turn Serie RZT-S Gebruiksaanwijzing - Deutsch - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info