495078
16
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
Operating Instructions English
13
The recommended tyre operating
pressure is:
front: 0.7 bar
rear: 0.7 bar
Over-inflating reduces the longevity
of the tyres. Tyre pressure should be
checked before every journey.
After 5 operating hours
First engine oil change. See engine
manual for subsequent intervals.
Use the oil channel or (optional)
quick oil drain (Figure 18).
Every 10 operating hours
Remove dirt and grass clippings
from under the V-belt cover of the
cutter deck (fig. 24).
Lubricate all cutter shafts, idlers,
and idler mounts with 251HEP
type grease applied to their
respective grease nipples.
This work should be performed
at a specialised workshop
Every 25 operating hours
Using a multi-purpose grease,
lubricate the front wheels on the
cutter deck frame via the grease
nipples (depending on model).
Lubricating the steering
mechanism:
Fig. 19
Lubricate wheel bearings and
axles of the rear wheels via the
grease nipples (2) with grease
type 251HEP*.
Lubricate both steeting arms
(right and left) on the lubricating
nipples (1) with 251HEP*
grease.
* Use a commercially available
grease gun. According to the
model, a grease gun is enclosed.
Note
If the power needed increases when
steering, i.e. steering is made
difficult, grease earlier.
Every 50 operating hours
Grass residue and other soiling on
the drive gears must be removed
at a specialised garage.
Every 2 months
For battery type 2 only – Fill battery
cells with distilled water up to 1 cm
beneath the filling aperture.
If necessary
Servicing the battery.
Always keep the battery clean.
Avoid tipping the battery.
Battery acid may leak out!
Grease battery poles with terminal
grease.
Charging the battery
When the appliance is not used for
longer periods, we recommend
removing the battery from the
appliance and charging this before
and every two months during
storage and before the appliance
is again put into operation.
Note
Note the information in the operating
instructions for your battery charger.
Replace the fuse
Replace defect fuses only with the
equivalent rating.
Cleaning the steering gear
If spoadic steering difficulties or
a steering block is experienced
clean the steering gear mechanism
see “once a season”.
If that does not solve the problem,
visit a garage.
Once a season
Cleaning the steering gear:
Take away the cover
(3, Fig. 19).
Clean the steering gear
cogwheels (right and left).
Lubricate all moving parts and
bearing surfaces with a few drops
of oil (control levers, cutting height
adjustment).
Clean the spark plug and check
the gap between the electrodes
or replace the plug. See engine
handbook.
Have a repair shop lubricate the
wheel axles with special grease
(water-repellent).
Have the cutting blade sharpened
or replaced in a specialist
workshop.
Setting the cutter deck
t~êåáåÖ
oáëâ=çÑ=áåàìêó=íÜêçìÖÜ=íÜÉ=ÉåÖáåÉ=
ÄÉáåÖ=ìåáåíÉåíáçå~ääó=ëí~êíÉÇK
mêçíÉÅí=óçìêëÉäÑ=Ñêçã=áåàìêóK=
_ÉÑçêÉ=~ää=ïçêâ=çå=íÜáë=ìåáí
Ó é~êâ=íÜÉ=~ééäá~åÅÉ=çå=~=äÉîÉä=
ëìêÑ~ÅÉ
Ó íìêå=íÜÉ=ÉåÖáåÉ=çÑÑI
Ó êÉãçîÉ=íÜÉ=áÖåáíáçå=âÉóI
ÓëïáíÅÜ=çÑÑ=mqlI
Ó äçÅâ=íÜÉ=é~êâ áåÖ=Äê~âÉI
Ó ï~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=
ÅçãÉ=íç=êÉëí=~åÇ=íÜÉ=ÉåÖáåÉ=Ü~ë=
Ñìääó=ÅççäÉÇI
Ó êÉãçîÉ=íÜÉ=ëé~êâ=éäìÖ=ÅçååÉÅíçê=
çå=íÜÉ=ÉåÖáåÉ=áå=çêÇÉê=íç=éêÉîÉåí=
íÜÉ=ÉåÖáåÉ=Ñêçã=~ÅÅáÇÉåí~ääó=ÄÉáåÖ=
ëí~êíÉÇK
t~êåáåÖ
oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=ÅìííáåÖ=
Ää~ÇÉ
tÉ~ê=éêçíÉÅíáîÉ=ÖäçîÉëK
When mowing does not appear to
be parallel to the lawn the cutters
can be aligned.
Note
Before aligning the cutters check the
tyre pressure on the appliance.
Setting the side level
Fig. 20
Raise the cutters to the top
(medium height position)
Carefully turn the outer cutters
(risk of injury) transverse to the
drive direction.
Measure the distance between the
ground and the ends of the two
outer cutters. The result should
be the same.
If required, set the correct level by
adjusting the lifting cable (3, on left
or right). To do this, loosen the lock
nut (1) and set the correct level by
adjusting the nut (2). After setting
the level, retighten the lock nut.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD Zero Turn Serie Frontcut bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD Zero Turn Serie Frontcut in de taal/talen: Engels als bijlage per email.

De handleiding is 2,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van MTD Zero Turn Serie Frontcut

MTD Zero Turn Serie Frontcut Gebruiksaanwijzing - Nederlands - 18 pagina's

MTD Zero Turn Serie Frontcut Gebruiksaanwijzing - Deutsch - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info