507836
16
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
Operating instructions for lawn tractors English
13
The rear axles must be lubricated
with a special-purpose (water-
repellent) grease at a specialised
garage.
Have the cutting blade sharpened
or replaced in a specialist
workshop.
Note
Regularly check (when visiting
your workshop) the condition
of the mower deck V-belt.
Installing/removing and
adjusting cutter deck
a~åÖÉê
oáëâÑåàìêóêçãåÖáåÉí~êíáåÖ=
ìåáåíÉåíáçå~ääó
mêçíÉÅí=óçìêëÉäÑ=Ñêçã=áåàìêóK=_ÉÑçêÉ=
ÇçáåÖ=~åó=ïçêâ=íç=íÜáë=~é éäá~åÅÉ W
Ó é~êâ=íÜÉ=~ééäá~åÅÉ=çå=~=äÉîÉä=
ëìêÑ~ÅÉI
Ó íìêå=íÜÉ=ÉåÖáåÉ=çÑÑI
Ó êÉãçîÉ=íÜÉ=áÖåáíáçå=âÉóI
Ó ëïáíÅÜ=çÑÑ=mqlI
Ó äçÅâ=íÜÉ=é~êâáåÖ=Äê~âÉI
Ó ï~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=
ÅçãÉ=íç=êÉëí=~åÇ=íÜÉ=ÉåÖáåÉ=Ü~ë=
Ñìääó=ÅççäÉÇI
Ó êÉãçîÉ=íÜÉ=ëé~êâ=éäìÖ=ÅçååÉÅíçê=
çå=íÜÉ=ÉåÖáåÉ=áå=çêÇÉê=íç=éêÉîÉåí=
íÜÉ=ÉåÖáåÉ=Ñêçã=~ÅÅáÇÉåí~ääó=ÄÉáåÖ=
ëí~êíÉÇK
a~åÖÉê
oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=ÅìííÉêëK
tÉ~ê=éêçíÉÅíáîÉ=ÖäçîÉ ëK
Assembly
Note
Work proceeds faster when you
are assisted by a second person.
Mounting the cutting
mechanism
Move the cutting height setting
lever into the top catch (HI/16).
or
For units with electric cutter deck
lifter: Move lever for setting the
height/depth to the lowest position
(LO/1) and press the switch
for the electric lifter backwards.
Push cutter deck from the right side
under the tractor.
Fig. 19
Align cutter deck so that the rear
cutter deck holders (1) are under
the locating holes (2) of the lifting
arms (3).
Lower lifting arms (3):
Move cutting height adjustment
lever to the lowest notch (LO/1).
or
For units with electric cutter
deck lifter: Press switch for
the electric lifter forwards.
Fig. 20
Pull out the J-handle (1) on the left
cutter deck holder (2). Lift the back
of the cutter deck slightly until you
can press the J-handle into the
locating hole of the lifting arm (3).
Ensure that it engages correctly.
Repeat this work step on the right
side of the cutter deck.
Fig. 21
Remove the two nuts from the
fixing bracket (1).
Attach fixing bracket (1) to the
holders (2) on the cutter deck.
Insert the ends of the fixing bracket
into the locating holes of the holder
(3) on the tractor.
Screw the two nuts back onto
the fixing bracket.
Note: Do not tighten the nuts yet.
Attaching the drive belt
Note
The “V” side of the drive belt must
be in the belt pulleys.
Fig. 22
Place drive belt (1) on the engine
coupling belt pulley (2) (PTO).
Feed drive belt downwards and
place on the two deflection belt
pulleys (3).
Note: On the right deflection belt
pulley the V-belt guide (4) must
be bent outwards slightly so that
the drive belt can be attached.
After attaching the drive belt, bend
V-belt guide back!
Feed drive belt backwards and
attach it to the cutter deck.
Fig. 23
Press belt pulley holder (1) on
the cutter deck backwards,
the belt pulley moves forwards.
Place the drive belt on the belt
pulley (1, Fig. 24). Slowly feed the
belt pulley holder back.
=oáëâ=çÑ=áåàìêóK
qÜÉ=ÄÉ äí= é ìääÉó=ÜçäÇÉê= áë=ìåÇÉê= ëíêçåÖ=
ëéêáåÖ=íÉåëáçå=Ó=ïçêâ=ïáíÜ=ÉñíêÉãÉ =
Å~ìíáçå>
Check that the drive belt is positio-
ned correctly on all belt pulleys.
Installing the spacer (stop
for the cutter deck lifter)
Fig. 25
Note
The spacer must be installed before
the cutter deck is set.
Using the screws (2), attach
the two holders (1) to the right and
left sides of the tractor frame.
Note
If the cutter deck has a cutting width of
107 cm, only one
spacer is attached
to the left
side of the tractor frame.
Removing the transport secu-
ring device at the ejector flap
Fig. 18
Depending on the model remove
the locking plate or cable tie.
The deflector closes automatically.
Setting the cutter level
t~êåáåÖ
^ÑíÉê=áåëí~ääáåÖ=íÜÉ=ÅìííÉê=ÇÉÅâI=
ëÉí=íÜÉ=ÅìííÉê=ÇÉÅâ=äÉîÉäK
Note
Before aligning the cutters check
the tyre pressure on the appliance.
Set the level from front to back.
Fig. 26
Move the cutter deck to a medium
height position.
Carefully turn the outer cutters
(risk of injury) parallel to the drive
direction.
Measure the distance between
the ground and the end of the right
cutter. The end of the front cutter
should be about 6–10 mm lower
than the end of the rear cutter.
You may have to adjust the front
receiver (1). Set the correct level
by adjusting the nuts (2) equally.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

MTD-CubCadet-serie-2000

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD CubCadet serie 2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD CubCadet serie 2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van MTD CubCadet serie 2000

MTD CubCadet serie 2000 Gebruiksaanwijzing - Nederlands - 19 pagina's

MTD CubCadet serie 2000 Gebruiksaanwijzing - Deutsch - 19 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info