672424
11
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
English Operating manual
8
Insert retaining bar (6) through
the openings (3, 4, 5) in order
to secure the gearbox.
While holding the retaining bar (6),
attach the cutting blade (7) with
blade holder (8), retaining bell (9)
and nut (10) as follows:
Push cutting blade (7) onto
drive shaft (2) and centre on
the spacer (1).
Note
Ensure that the cutting blade (7) is
seated correctly on the spacer (1),
i.e. centred and resting flat!
Attach blade holder (8),
retaining bell (9) and nut (10).
Ensure that the blade holder is
seated correctly in the toothing!
Tighten nut firmly anti-clockwise
(to the left) – tightening torque
37 Nm.
Note
Before tightening, check again that
the cutting blade is seated correctly.
If you do not have a torque wrench,
tighten the nut firmly by hand.
Then tighten the nut anti-clockwise
(to the left) another half turn using
a ring spanner.
Remove retaining bar from the
gear head.
Remove guard (if fitted) from
the cutting blade.
Removing the cutting blade
Fig. 8
Attach guard (if available) to the
cutting blade.
Align the openings (3, 4, 5).
Insert retaining bar (6) through the
openings and hold in position.
Unscrew nut clockwise (to the right).
Remove cutting blade (7), blade
holder (8) and retaining bell (9)
(Fig. 7).
Oil and petrol
Oil
Use quality oil only, API classification
TC (TSC-3) which is offered for air-
cooled two-stroke engines.
Mix the oil for two-stroke engines
according to the instructions on
the container, 1:40 (2.5 %).
Petrol
a~åÖÉê=
råÇÉê=ÅÉêí~áå=ÅçåÇáíáçåë=éÉíêçä=áë=
ÉñíêÉãÉäó=Ñä~ãã~ÄäÉ=~åÇ=ÉñéäçëáîÉK
Ó oÉÑìÉä=çåäó=áå=~=ïÉää=îÉåíáä~íÉÇ=~êÉ~=
~åÇ=ïáíÜ=íÜÉ=ÉåÖáåÉ=ëïáíÅÜÉÇ=çÑÑK=
aç=åçí=ëãçâÉ=~åÇ=ëïáíÅÜ=çÑÑ=~ää=
áÖåáíáçå=ëçìêÅÉë=áå=íÜÉ=îáÅáåáíó=çÑ=íÜÉ=
í~åâ=çê=~í=íÜÉ=ÑìÉä=ëíçê~ÖÉ=ÇÉéçíK
Ó aç=åçí=çîÉêÑáää=íÜÉ=ÑìÉä=í~åâ=EíÜÉêÉ=
ãìëí=ÄÉ=åç=ÑìÉä=áå=íÜÉ=áåäÉí=åçòòäÉFK=
^ÑíÉê=ÑáääáåÖ=ìé=íÜÉ=éÉíêçä=í~åâI=
ÉåëìêÉÜ~íÜÉ~åâ~éëäçëÉÇ=
~åÇ=ëÉÅìêÉÇK
Ó tÜÉå=ÑáääáåÖ=ìé=íÜÉ=éÉíêçä=í~åâI=Çç=
åçí=ëéáää=~åó=ÑìÉäK=péáääÉÇ=ÑìÉä=çê=
éÉíêçä=î~éçìêë=ã~ó=áÖåáíÉK=fÑ=ÑìÉä=
Ü~ë=ÄÉÉå=ëéáääÉÇI=ÉåëìêÉ=íÜ~í=íÜÉ=
~êÉ~=áë=ÇêáÉÇ=ÄÉÑçêÉ=íÜÉ=ÉåÖáåÉ=áë=
êÉëí~êíÉÇK
Ó mêÉîÉåí=êÉéÉ~íÉÇ=çê=éêçäçåÖÉÇ=
ëâáå=Åçåí~Åí=çê=áåÜ~ä~íáçå=çÑ=íÜÉ=
î~éçìêëK
`~ìíáçå
aççíáääéáíÜìÉäÑéÉÅáÑáÅ~íáçå=
bURK=fÑ=ÑìÉä=çÑ=ëéÉÅáÑáÅ~íáçå=bUR=
EÉíÜ~åçäçåíÉåí=[NR=BFëëÉÇIÜÉ=
ÉåÖáåÉ=ã~ó=ÄÉ=Ç~ã~ÖÉÇK=
qÜÉ=ìëÉ=çÑ=~å=ìå~ìíÜçêáëÉÇ=ÑìÉä=ïáää=
îçáÇ=íÜÉ=ï~êê~åíóK=
See instructions on mixing
oil and petrol
Age and/or incorrectly mixed fuel are
the main reasons for the unit not
running properly.
Always use clean, fresh unleaded
petrol (no more than 60 days old,
minimum octane number 91 ROZ).
Follow exactly the instructions for
the correct petrol/oil mixture.
Correctly mix two-stroke engine oil
and lead-free petrol, 1:40 (2.5 %).
Do not mix directly in the tank.
Fill the tank with petrol.
Fig. 1
Remove tank cap (4).
Fill fuel tank with petrol/oil mixture.
Never overfill!
Close fuel tank tightly.
Move the unit approx. 10 m from
the filling station/fuel container
before starting the engine.
Operation
a~åÖÉê=
aç=åçí=Üççâ=íÜÉ=ëÜçìäÇÉê=ëíê~é=çåíç=
íÜÉ=ìåáí=ìåíáä=íÜÉ=ÉåÖáåÉ=Ü~ë=ëí~êíÉÇK
Mix petrol (gasoline) with oil.
Fill the tank with the mixture.
See „Oil and petrol“.
Starting the engine
Starting the cold engine.
Fig. 9
Press throttle lock (2) and press
the throttle (3) all the way and hold
in position.
Move the ignition switch (1) to
the START position.
Release throttle lock and throttle.
Note
Both levers remain locked in the
depressed position (cold start
position).
Slowly and fully press intake
pump/primer (5) 6x (Fig. 10).
The fuel must be visible in the
pump. If this is not the case,
keep pressing until fuel is visible.
Move choke lever (6) to position
1/ (Fig. 11).
Press the unit on the ground.
Slowly pull on the starter cable (7)
until it begins to resist. Then pull
quickly and forcefully until the
engine starts (Fig. 12).
After starting the engine, do not let
the pull-starter spring back, but
slowly guide it back.
Leave the engine running for
approx. 1–2 minutes.
Move choke lever (6) to position
2/ and leave the engine to
warm up for another 1–2 minutes
(depending on the outside
temperature) (Fig. 11).
!
!
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD 1043 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD 1043 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van MTD 1043

MTD 1043 Gebruiksaanwijzing - Nederlands - 16 pagina's

MTD 1043 Gebruiksaanwijzing - Deutsch - 16 pagina's

MTD 1043 Gebruiksaanwijzing - Français - 17 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info