603182
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
SETUP YOUR CAMERA FIRST
STEP 1
SET UP YOUR CAMERA ON THE
WIRELESS LOCAL NETWORK
STEP 3
DISCOVER & VIEW YOUR CAMERA ON
THE LOCAL NETWORK
STEP 2
LN Series
Quick Setup Guide
It really is that easy!
Identify Your IP Camera
BEFORE YOU START
This Network Camera is designed for easy installation.
However, before you continue, please read the following:
The Quick Start Guide refers to LNE1001, LNE3003 and LNZ4001
models and must be followed in sequence without
skipping steps.
1. When setting up the camera, use Internet Explorer only
After the initial setup, you can view the camera using Internet
Explorer (with ActiveX), Mozilla Firefox and
Safari
2. Steps 1 - 2 should to be completed when your camera is
connected wired before you can use the camera wirelessly.
3. When connecting the camera to a wireless network, consider the
following:
a. If your wireless router is not set up with wireless encryption, you
can start the installation process immediately.
b. If your wireless router is set up with the encryption, please make
sure you know the encryption key. If you do not know the
encryption key (encryption password), please refer to your
router’s manual in order to reset the key.
c. If your wireless router is set up with a different type of encryption
please refer to your router’s manual in order to change
encryption type to WEP - OPEN, WPA - PERSONAL,
WPAZ - PERSONAL.
d. The camera is compatible with Macintosh for viewing only.
Recording on Macintosh is not supported. When using
Macintosh auto discovery “Bonjour” advanced
knowledge is required. Please refer to “Setting Up Using
Macintosh” FAQ on LOREX web site www.lorextechnology.com
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Hand Tools Skills - Easy
BASIC INSTALLATION GUIDE
Broadband Router and Computer are required for
local and remote monitoring (not included).
Place the base of the
camera on a flat surface
and screw on the stand.
a
Attach the screw knob to
the camera stand.
b
Attach the wireless antenna to
the back of the camera.
c
Screw the camera to the
camera stand.
d
Tighten the screw knob to
secure the camera.
e
Plug the power adaptor into the
power port of the camera. Plug the
other end to an electrical outlet.
NOTE: Make sure the LED is lit
on the front of the camera. If not,
check that all cables are properly
connected.
g
Set up Your Camera*
f
Connect the included network
cable to the rear side of the
LAN port on the bottom of the
camera. Connect the other
end of the network cable to the
router, switch, or active wall
port of your local network.
IMPORTANT
5. Reset
6. Audio IN
7. Audio OUT
8. I/O
1. Camera
2. Antenna
3. Power Adaptor Port
4. Ethernet Cable
(LAN) Port
2
1
4
3
5
3
5
4
2
1
6 7 8
LNE3003
LNZ4001
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Hand Tools
- Computer
Skills - Easy
BASIC INSTALLATION GUIDE
NOTE: This quick start guide refers to a Windows 7 & Vista™ installation.
NOTE: For initial setup, you will need Internet Explorer (on PC using
Windows Operating system only) as your default browser. Do not install
DigiConsole until Step 2 is completed.
Launching the DigiConsole Software
Before launching the program, please make sure your computer is connected
to the same local network as the camera and has access to the Internet.
The camera must be connected using the included Ethernet cable for initial
installation. It is recommended to setup the camera when your computer is
wired to the local network. If you are using the wireless connection on your
computer, please make sure you are connected to your wireless router (check
wireless name - SSID).
Congratulations! Your camera is
now set-up for local viewing
If the software runs
automatically, please
proceed to Step 2, section d.
If the pop-up window
appears, click Run
Setup.exe and continue to
Step 2, section c.
b
Double-click the camera to
launch DigiViewer in your
browser.
a
Enter admin in the username
and admin in the password
fields to access your camera.
The browser will prompt you
to install ActiveX.
b
Depending on your browser
security settings, you can use the
“remember me” check option and
the next time you will view the
same camera using this browser
it will renumber user name and
password till you restart your
computer.
Did you know?
If a security pop-up window
appears, click Unblock
and Continue to allow
DigiConsole to run.
c
NOTE: If the CD does not start
automatically, please go to “Computer”
(“My Computer” for Windows XP™ users)
and double click on the CD Drive to run
the application. Follow Step 2.
Click Find to discover Lorex
cameras on your network.
OPTION: If UPNP is enabled on your
computer open the “Network” (“My
Network Places” for Windows XP™
users) folder to view UPnP devices.
(UPNP is disabled by default in
Windows Vista™).
d
a
Insert the included
DigiConsole Software CD into
your CD/DVD-ROM drive.
Local Viewing
d
If a security pop-up window
appears, click Unblock
and Continue. Click the
warning on the browser bar
and select Install ActiveX
Control. Click Unblock or
Continue in any proceeding
security pop-ups.
c
Click the warning bar (it will turn from
yellow to blue) and select Install ActiveX.
Click Install to start the
installation. Click Unblock or
Continue in any security
pop-up. (This step is required
only for first time set-up).
Setting up Wireless Connectivity
CAMERA must be PLUGGED INTO YOUR ROUTER BEFORE STARTING THE
WIRELESS SETUP. Steps 1 - 2 should to be completed.
From DigiViewer, click
Settings and then click
Wireless. DigiViewer
automatically scans for any
wireless networks.
a
Click Submit Wireless. Allow
DigiViewer a few moments
to apply your new connection
settings.
NOTE: Changing wireless
settings may require devices
to reconnect.
c
1. Click on Settings,
Preferences. Beside
“Wireless IP Address”,
there should be a populated
IP address. This means that
the wireless connection has
been connected.
2. Disconnect the network cable
from the camera.
3. Double-click the camera in
the the Windows Network
menu (Start>Network) to
launch DigiViewer in your
default browser.
NOTE: If using a Mac, use
Bonjour in Safari to auto-detect
your camera.
d
If not already enabled, select
Enabled from the Wireless
Mode drop-down menu.
From the list of available
networks, select the wireless
network for the device. If
protection/encryption is
enabled on the wireless
router, you must enter the
network password.
b
Congratulations! Your
camera is now set-up to
work Wireless.
ATTENTION: This section is applicable to wireless camera models only. The
cameras are B/G wireless devices. N wireless routers must be in “mixed B & G”
mode (not in N mode) to detect the camera.
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Hand Tools
- Computer
Skills - Easy
BASIC INSTALLATION GUIDE
Information in this document is subject to change without notice. As our products are
subject to continuous improvement, Lorex Technology Inc. and our subsidiaries reserve
the right to modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE © 2010 LOREX. All rights reserved.
For detailed setup information, please refer to
the User’s Manual included inside the software/
support CD . For additional information, please
visit our website
www.lorextechnology.com
It’s all on the Web
LNE1001 LNE3003 LNZ4001
Enhance your security with genuine Lorex Cameras, Digital Video Recorders,
Integrated Systems and Accessories. Order whatever you need at
www.lorexcctv.com or call 1-888-42-LOREX (1-888-425-6739)
SEE HEAR PROTECT
PROTECT EVERYTHING
THAT MATTERS
Warehouse
LNP5220E, LNP5320E,
LND7220V, LNZ9320W
Offi ce
LNE3003 , LNP5220E,
LND7220V
Day Care
LNE3003, LNP5220E
Convenience Store
LND7220V, LNE3003
LNP5220E, LND7220V
Restaurant
Home Offi ce
LNE3003
Add wired or wireless network cameras to
expand the “Envelope of Protection” for your
business, your home and your family
Drive Way / Parking Lot Front Door
LNE3003
Nursery
LNE3003
Backyard
LNP5320E, LND7220VLNP5320E, LNB6300V
LNZ4001
LNE1001
Available to Purchase:
16-CHANNEL INTELLIGENT SURVEILLANCE SOFTWARE
SOLUTION
LDP1601
www.lorextechnology.com
* camera mounting options may vary by model.
LN Series_QSG_EN_R2
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lorex LNE1001 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lorex LNE1001 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info