756997
13
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
24
User Manual
Lorenz AIS 3000 RT
Fixing Template (NOT TO SCALE)
13
User Manual
Lorenz AIS 3000 RT
Green (Unit operating OK)
Yellow (Warning)
Red (Fault)
Blue
(Status)
S
Using the transponder
Switching on
When the 12V supply is switched on all four LEDs visible on the front panel of the unit will illuminate twice for a period of one
second on each illumination. The red and blue LEDs will then go out. When the internal GPS starts outputting valid position
information and the Lorenz AIS 3000 RT unit transmits its first position report (message 18) the yellow LED will go out; note that
this process may take up to 30 minutes depending on the switch-on state of the GPS receiver. When the yellow LED goes out
the green LED will illuminate indicating that the unit is now operating
correctly.
Switch functions
The blue switch on the front of the unit can be configured either to
trigger transmission of a "Safety Related Message" or to place the unit
into "Silent mode". This choice is made during configuration of the unit
using the proAIS application; please refer to the proAIS user guide for
further information on the configuration options.
When configured to transmit a "Safety Related Message" the button will initiate broadcast of an AIS message containing the
vessels MMSI along with the text "MAYDAY MAYDAY". The button must be pressed for at least two seconds to initiate this
transmission and the blue LED will illuminate to indicate the message has been sent. Additional "Safety Related Messages" can
not be sent until the blue LED has extinguished which will occur one minute after an SRM has been sent.
When configured to place the unit into "Silent mode" each press of the switch will toggle the AIS transmitter on or off. The switch
must be depressed for two seconds to change the state of the transmitter. When the transmitter is off, the yellow "Warning" LED
and blue "Status" LEDs will be illuminated and the transponders position will not be broadcast to other vessels. The position of
other vessels will still be received by the unit.
Warning and fault states
If the unit has not been able to transmit a position report during the last expected two reporting intervals (i.e. the nominal
reporting interval cannot be maintained for operational reasons such as a Message 23 quiet period, high channel load
conditions, etc) the yellow LED will illuminate. This is a warning condition only and indicates that your vessels position is not
currently being reported to other vessels. Reception of other vessel AIS information by the AIS 3000 RT is not affected. When
the unit is able to commence reporting the yellow LED goes out.
If a fault occurs the red LED will illuminate. This may illuminate briefly if the power supply is interrupted or if the VHF antenna
characteristics are briefly affected.
If the Red LED illuminates continuously the unit should be assumed to be faulty and should either be switched off (power
removed) or if this is not practical any other vessel position information derived from the unit should not be used and it should
also be assumed that the unit is not transmitting valid position information for your vessel.
The unit should be examined by a competent equipment maintainer at the earliest opportunity.
Data port messages
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lorenz AIS 3000 RT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lorenz AIS 3000 RT in de taal/talen: Engels als bijlage per email.

De handleiding is 1,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info