715301
5
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
13
Putting into operation
* Depending on model and options
NOTICE
Risk of damage to the appliance due to overheating with
insucient ventilation!
The compressor may be damaged with insucient
ventilation.
Ensure sucient ventilation.
Observe the ventilation requirements.
4.5 Disposing of packaging
WARNING
Danger of suocation due to packing material and
plastic lm!
Do not allow children to play with packaging material.
The packaging is made of recyclable materials:
- corrugated board/cardboard
- expanded polystyrene parts
- polythene bags and sheets
- polypropylene straps
- nailed wooden frame with polyethylene panel*
Take the packaging material to an ocial collecting point.
4.6 Connecting the appliance
NOTICE
Failure to connect properly
Damage to the electronics.
Do not use a standalone inverter.
Do not use an energy saving plug.
WARNING
Failure to connect properly Fire.
Do not use an extension cable.
Do not use distributor blocks.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It must
be outside the area of the rear of the appliance.
Check the electrical connection.
Plug in the power plug.
4.7 Switching on the appliance
Note
To switch on the entire appliance it is necessary only to switch
on the freezer compartment. In so doing, the refrigerator
compartment is automatically switched on as well.
The appliance should have been operating for about 2 hours
before you stock it with frozen food. Only place frozen goods in
the freeze compartment once the temperature display shows at
least -18°C.
4.7.1 Switching on the freezer compartment
Press On/O button for the freezer section Fig. 11 (9).
The appliance is switched on. The temperature display shows
the set temperature. The temperature display for the freezer
section and the alarm symbol ash until the temperature is
cold enough.
4.7.2 Switching on the refrigerator compartment
Note
When the refrigerator compartment is switched on, the freezer
compartment is automatically switched on as well.
If the efrigerator compartment was switched o (e.g. with an
extended absence due to holiday), this can be switched on again
separately.
be at least 1 m�. Information on the coolant is on the model
plate inside the appliance.
Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because
otherwise there will be vibratory noise!
Remove the protective lm from the outside of the appliance.*
Remove all transit supports.
The spacers supplied with some appliances must be used to
achieve the stated energy consumption. These will extend the
depth of the appliance by approx. 35 mm. The appliance is fully
functional if the spacers are not used, but does have a slightly
higher energy consumption.
Fig. 9 In the case of an appliance with enclosed wall spacers,
mount the wall spacers on the back of the appliance at the top
left and right.
Dispose of packaging material. (see 4.5)
Fig. 4
Align the appliance so that it stands firmly and
on a level by applying the accompanying spanner to the
adjustableheight feet (A) and using a spirit level. Then support
the door: Extend the adjustable foot at the turn hinge (B) until
it rests on the oor and then make a further 90° turn.
Note
Clean the appliance (see 6.2).
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
Always see to good ventilation at the installation site.
4.3 Changing over the door hinges
You can change over the door hinges if necessary:
see assembly instructions provided.
Ensure that the following tools are to hand:
q Torx® 25
q Screwdriver
q Cordless screwdriver, if necessary
q Second person for tting work, if needed
Note
Remove any food from the door racks before removing the
door, so that no food falls out.
CAUTION
Risk of injury if the door tips!
Take good hold of the door.
Set down the door carefully.
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place rmly enough,
the door may drop out. This may lead to severe injuries. What is
more, the door may not close and therefore the appliance may
fail to cool properly.
Screw the turn hinges rmly into place with 4 Nm.
Check all of the screws and retighten if necessary.
4.4 Insertion into a row of kitchen units
The appliance can be built into kitchen units.
see assembly instructions provided.
Ventilation requirements:
A [mm] B [mm] C [cm
2
] D [mm] E [mm]
655
x
75 min. 300 min. 50 min. 19
x
For appliances supplied with wall spacers, the measurement
increases by 35 mm (see 4.2).
The appliance may protrude further, depending on the depth of
the kitchen units and the use of wall spacer brackets.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Liebherr CN 4713 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Liebherr CN 4713 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Liebherr CN 4713

Liebherr CN 4713 Gebruiksaanwijzing - Nederlands - 10 pagina's

Liebherr CN 4713 Gebruiksaanwijzing - Deutsch - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info