775459
24
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
20
where they thread into the crank arms.
Note: There are right and left pedals,
usually marked with a letter stamped
on the end of the pedal axle, or on the
wrench flats.
1. Remove the pedals; turn the right
pedal spindle counter-clockwise, but
turn the left clockwise.
2. Apply a this layer of grease over all
the threads.
3. Install the pedals on the proper
side; put the right pedal on the right
crank arm and the left pedal on the
left crank arm.
4. Tighten the pedals.

Every month, lubricate all pivot points
on both the front and rear derailleurs,
including the derailleur pulleys on the
rear derailleur, with chain lube.

Once a year re-grease the headset
bearings.

Every 3 months lubricate your brake
lever pivots and brake arm fixing
pivots with a light oil.

Once a year re-grease the wheel
bearings.
Every year, lubricate wheel quick-
release. Apply several drops of
Wrench Force® synthetic lube or a
similar light oil where the quick-
release lever rotates in the quick-
release body.

Once a month, apply a light oil to the
upper fork leg where the lower leg
slides on it. Wipe clean.

No lubrication is required for the
shock or the pivot of your full suspen-
sion bike. Avoid all lubricants.

Lubricate cables whenever they are
installed.

Installing a cable in a cantilever brake
requires special tools and training, so
should only be done by your dealer.
1. Note the path of the old cable, and
loosen the cable anchor bolt and
remove the worn cable.
2. Grease the new cable and reinstall,
feeding it along the same path as
the old cable, including through the
cable anchor bolt.
3. Make sure the leaded cable-end is
seated properly in the lever, and the
housing is properly seated in the
lever.
If needed when installing a cable in a
brake, readjust the brake.
4. Turn the adjusting barrel clockwise
so the threads on the adjusting
barrel are not exposed.
For a shift cable, put the shifter in the
position with the least cable tension.
For a brake, hold the brake closed
while you do the next step.
5. Tighten the cable clamp bolt:
52-69 lb•in. (6-8 Nm)
6. Cut the cable so that no more than
2 inches (51mm) extends beyond the
anchor bolt.
7. Crimp a metal cap or place a bit
of solder on the end of the cable to
prevent fraying.
8. Follow the instructions for adjust-
ment.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw LeMond Bicycles bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van LeMond Bicycles in de taal/talen: Engels als bijlage per email.

De handleiding is 5.88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info