680891
101
Verklein
Vergroot
Pagina terug
1/2025
Pagina verder
Default:
2
0
Special values:
2
0 disables the time limit. The LL2M server stays permanently enabled in this state.
3.11.3 Commands for the LL2M client
For every LL2M command, an encrypted tunnel is set up that protects the log-in information transferred on transmission.
To use the integrated LL2M client, start a Telnet session on a LANCOM that has local access to the LL2M server via the
available physical medium (LAN, WLAN). The following commands can be used to contact the LL2M server in this console
session.
5
You must have root rights on the LL2M server to run commands on the LL2M client.
1
LL2Mdetect
The LL2M client uses this command to send a SYSINFO request to the LL2M server. The server then sends its system
information, such as hardware and serial number, back to the client for display. The LL2Mdetect command can be
restricted using the following parameters.
2
-a <MAC address>: Restricts the command to those devices with the specified MAC address only. The MAC
address is specified in format “00a057010203”, “00-a0-57-01-02-03” or “00:a0:57:01:02:03”.
5
If no MAC limitations are set, the detect is sent as a multicast (or optionally as a broadcast) to all
LL2M-compatible devices. To contact groups of MAC addresses, * and x can by used as placeholders in
individual MAC address positions, e.g. “00-a0-57-xx-xx-xx” for all LANCOM MAC addresses.
2
-t <device type>: Restricts the command to those devices of the corresponding hardware type only.
2
-r <hardware release>: Restricts the command to those devices with the corresponding hardware release only.
2
-f <version>: Restricts the command to those devices with the corresponding firmware version only.
2
-s <serial number>: Restricts the command to those devices with the corresponding serial number only.
2
-b : Sends the LL2Mdetect request as a broadcast and not as a multicast.
2
-v <VLAN ID>: Only sends the LL2Mdetect request on the VLAN specified. If no VLAN ID is specified, the VLAN
ID of the first defined IP network is used.
Example:
2
ll2mdetect -r A: This command sends a SYSINFO request to all devices with hardware release “A”.
The response from the LL2M server contains the following information:
2
Device name
2
Device type
2
Serial number
2
MAC address
2
Hardware release
2
Firmware version with date
1
LL2Mexec
The LL2M client uses this command to send a single-line command to run on the LL2M server. Several commands
can be combined in one LL2M command by using semicolons as separators. Depending on the command, either the
actions are run on the remote device and the responses from the remote device are sent to the LL2M client for display.
The LL2Mexec command conforms to the following syntax:
2
ll2mexec <user>[:<password>]@<MAC address>
The LL2Mexec command can be restricted using the following parameters.
101
Reference Manual
3 Configuration
101

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lancom LCOS 9.10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lancom LCOS 9.10 in de taal/talen: Engels als bijlage per email.

De handleiding is 54,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info