629288
71
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
71
lares
programming manual
PROGRAMMING SUMMARY
This paragraph summarizes programming options that ensure the proper functioning of Panel based on the
parameters dened by the norms listed on page 73. If these programming data are changed the Panel shall
NOT be compliant with these norms.
PROGRAMMING ALARM, TAMPER AND FAULTS EVENTS
EVENT PROGRAMMING OUTPUTS SECTION
PROGRAMMING DESTINATIONS
SECTION
Zone alarm
Partition alarm
Select the output associated with
imago siren (or relay output if you
are using third-parts sirens)
Select at least one destination
present on phonebook
Zone tamper
Partition tamper
Panel tamper
Controlled output tamper
Peripheral tamper
Missing Peripheral
Select the output associated with
imago siren (or relay output if you
are using third-parts sirens). You
must also select 'When system
armed' in 'Activate output' section
(output activation is required only
for the GRADE 2)
Select at least one destination
present on phonebook
Masking/Zone faults
Missing net
Low battery
Missing Ethernet
Missing PSTN line
GSM trouble
Fuse protection
Power supply faults
Low power supply voltage
Battery faults
Communication faults
System reset
Is not allowed to activate no
acoustic signaling device.
Select at least one destination
present on phonebook
If you programmed Zone alarm events, you do not need to program the partition alarm, and vice versa.
Similarly should be programmed Zone tamper and Partition tamper events.
ARMING AND DISARMING OPERATIONS ALLOWED
All options that allow to arm and disarm the System without the use of an adequate level of access do not
conform. In particular, you cannot bind arming mode to zones programmed as 'Command' or keys on the
keypad that has enabled the 'No PIN' option.
ALARMS TRANSMISSION
GRADE 3
Events should be transmitted to the alarm receiving center exclusively through GPRS network (via gemino
Communicator-ATS4) or Ethernet (in case of IP Panel) with SIA DC-09 communications protocol. On the
contacts page can be programmed the IP receiver to be selected as a destination. To enable events
transmission on IP you must turn on the 'Enable events on IP' option. You also need to enable a supervision
by selecting 'Enable supervision' or programming the receiver as the destination on 'Periodic Test' event. The
'Periodic Test' period, to be set on the options page, must be less than 300 minutes.
71

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ksenia Lares bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ksenia Lares in de taal/talen: Engels als bijlage per email.

De handleiding is 3,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ksenia Lares

Ksenia Lares Snelstart handleiding - Nederlands - 3 pagina's

Ksenia Lares Gebruiksaanwijzing - Nederlands - 40 pagina's

Ksenia Lares Gebruiksaanwijzing - Deutsch - 26 pagina's

Ksenia Lares Gebruiksaanwijzing - English - 40 pagina's

Ksenia Lares Gebruiksaanwijzing - English - 45 pagina's

Ksenia Lares Installatiehandleiding - English - 17 pagina's

Ksenia Lares Gebruiksaanwijzing - Français - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info