570561
2
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
2
Installation procedure
Step 1:
Invert the display and place it on a soft and fl at surface. Locate the mounting points on
the back of the display.
Many LCD manufacturers conform to VESA standards. The VESA standard defi nes
the physical mounting interfaces. The LCD mount conforms to VESA 75/100/200/400
patterns.
Plasma monitors come with a random set of holes.
Note! Do not over tighten the screws. This may cause damage to the display or
bracket.
Before you begin, determine the desired mounting location.
Step 2:
Assemble the wall plate using the hardware and wrenches provided.
Note! Tighten screws uniformly to prevent distortion that might affect the assembly
process. Do not tighten with excessive force. Failure to follow these instructions may
cause excessive stress to the screws, greatly reducing their strength.
Solid concrete wall assembly: Carefully inspect the area where the LCD\Plasma\
Projector mount is to be installed. Check for any damage or loose cement.
Caution! When drilling holes in a cement wall or wooden studs, be absolutely sure there
are no water pipes or electrical wiring behind the wall. Use the wall plate to mark the
positions of the drilling holes.
Drill holes 3” deep using a (10 mm) masonry drill bit. Insert the plastic anchors into the
hole and tap fl ush until the washer is even with the concrete surface. Place the back plate
onto the concrete surface and slowly tighten each nut onto its respective anchor.
Wood studs assembly:
Use a stud sensor (sold separately) to locate framing near the desired mounting position.
Note! Framing beams are typically 1-1/2”- 2” wide and spaced 16” on center. We
recommend locating more than one stud to fi nd a trend in stud spacing. Using a sharp
device penetrate the drywall to identify the true center of the stud. Using the wall plate
base as a template, position the wall plate base vertically. Mark the hole position on
the wall, making sure you use the center screw holes. Use a level to check horizontal
alignment of marks.
Step 3:
For tilting models, gently pull the left and the right upper edges of the display to extend
the mount to its desired display tilting angle. Using a Phillips screwdriver, adjust the tilt
mechanism to its desired position. LCD mount models are designed to maintain their
tilting angle by using fi nger tips on the back of the monitor. Keeping the display far from
the tilting mechanism, turn the Philips screw to its desired angle.
Step 4:
Once the mounting of the display is completed, you can tills move the display from side to
side to optimize the fi nal position of the display. Gently slide the unit from left to right over
the steel rods on the wall plate.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Konig Electronic TVS-KN-AVS500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Konig Electronic TVS-KN-AVS500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Zweeds, Fins als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Konig Electronic TVS-KN-AVS500

Konig Electronic TVS-KN-AVS500 Installatiehandleiding - Alle talen - 1 pagina's

Konig Electronic TVS-KN-AVS500 Gebruiksaanwijzing - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info