782830
22
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
22
Note: The alarm function is activated
at any moment and will indicate a rapid
increase of the internal temperature. In
addition an acoustical signal will sound.
Child lock - Key lock: If this
function is activated, no settings can
be changed. However, the key lock can
be disabled in the same way as it is
activated.
Fig. 7To switch the freezer on and o, press
and hold the ON/ OFF switch OK/
5S for at least 5 seconds. This allows
the freezer to be switched on and o
without using the mains plug.
Fig. 8If you need ice cubes fill the ice cube
tray with water. Place the ice cube
maker in the freezer and wait several
hours. If the liquid is suciently frozen,
turn the knobs (a, b) to the right and
then release them. The ice cubes fall
into the tray. If necessary shake the
ice cube maker together with the
collecting tray.
Adjust the side of the hinges
Attention
Make sure that the freezer stands safely
during work and cannot tilt.
Note:
If necessary, and if the premises require it,
the mounting of the doors can be changed.
To do this, follow below instructions in the
given order.
The following tools are required:
Socket wrench 8 mm, wrench 8mm, phillips
screwdriver, slotted screwdriver. Due to
the uniqueness of the appropriate tools,
those are not mentioned separately in the
following instructions.
For this work a dierent hinge holder and
cover are needed, which are provided with
the unit.
Caution
Pull out the mains plug!
The mounting should be performed by at
least 2 persons to avoid dangers.
1 Pull o the top cover. If necessary use a
plastic card or spatula to loosen the cap.
2 Disconnect the plug and socket.
3 During unscrewing hold the refrigerator door
or it might be damaged. Remove the three
screws of the top hinge.
4 Pull out the door and place it on a soft and
clean surface.
5 Remove the blind cap on the top of the
freezer (use a plastic card or spatula to help
loosen the cap) and insert it into the holes
on the right side.
6 Pull o the front panel and place the cable
as shown.
7 Make sure the LED light bar is seated in the
guides and attach the front panel back to
the front.
8 Loosen the two caps on the top of the door.
9 Insert the end of the cable into the hole and
close it with the blind cap.
10
Pull the other cable out and close the hole
with the cap having the cable gland.
11
Loosen the angled plate on the bottom of
the door and screw it on the other side. Do
not turn the metal plate and note that the
small holes must be placed on the plastic
pins while the screw hole and the tapped
hole must be aligned.
12
Loosen the three screws on the lower
hinge plate and remove it. If necessary tilt
the refrigerator to get better access to the
bottom side.
13
Unscrew the hinge pin and screw it back on
the other side.
14
Place the hinge plate on the left side into
position.
15
Tighten the hinge plate securely.
16
Place the door on the lower hinge pin.
17
Keep the door in position. Take the additional
hinge provided and insert the hinge pin into
the corresponding hole in the door. Hold the
hinge plate in position and screw it.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Koenic KFZ 521 E NF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Koenic KFZ 521 E NF in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2.22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info