588356
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
ENGLISH
8. Once the SLX is mounted, its angle can be fine tuned to obtain optimal directivity toward the
listening area.
CAUTION: DO NOT REMOVE THE MAGNETS ON THE REAR OF THE SPEAKER ENCLOSURE.
CAUTION: SYNERGY SLX SPEAKERS ARE NOT INTENDED FOR CEILING MOUNTING.
CONNECTIONS
Note: Proper connection of your speakers to your amplifier or receiver is vital to obtaining good
sound quality. Please follow these directions carefully. Sloppy connections can cause amplifier
malfunction or damage.
Klipsch Synergy SLX speakers are wired internally with multiple gauges of high-purity copper wire,
carefully selected and wound to ensure optimum signal transfer at all frequencies. You will obtain
best performance from your speakers if you connect them to your amplifier or receiver with similar
quality wire available from your dealer. We recommend that you use 18-gauge or heavier (lower-
gauge) stranded copper wire. Use a lower gauge (heavier) wire for longer runs to reduce the
amount of amplifier power lost due to the wire’s resistance.
BUT FIRST: TYPES OF CONNECTORS
Bare wire
— Pull the two conductors apart for about an inch and strip approximately
1/4"
of
insula
tion from the end of each. (A wire stripper will simplify this, but you can use an ordinary
pocket knife to cut around and through the insulation down to the wire.) Twist the strands of wire
on each individual conductor tightly together. Loosen the nuts on a pair of binding posts until the
holes through the metal posts are exposed,
then insert the bare wire through the holes.
Screw the
nuts down finger-tight on the wire. Make sure that no strands of wire are touching from one
binding post to the other or to any strands from the other conductor. Failure to observe this
precaution a
t either end of the connection can result in amplifier malfunction or dama
ge.
Pins — Many pre-made speaker cables are terminated with metal pins. Loosen the nuts on a
pair of binding posts until the holes through the metal posts are exposed,
then insert the pins
through the holes. Screw the nuts down finger-tight on the pins — do not over-tighten. Make
sure that there is no metal-to-metal contact between the two pins or binding posts. Failure to
obser
ve this precaution a
t either end of the connection can result in amplifier malfunction
or damage.
Spade lugs — Some speaker ca
bles are termina
ted with U-sha
ped connectors called spade
lugs. Loosen the nuts on a pair of binding posts and slip the spade lugs around the metal posts.
Screw the nuts down finger-tight on the lugs and inspect to ensure they have remained firmly
in place.
Make sure tha
t there is no metal-to-metal contact between the two lugs or binding
posts. Failure to observe this precaution at either end of the connection can result in amplifier
malfunction or damage.
OTHER TYPES OF SPECIALTY CONNECTORS ARE AVAILABLE TO FACILITATE HOOKING UP YOUR
SPEAKERS. PLEASE CONSULT YOUR AUTHORIZED KLIPSCH DEALER FOR SUGGESTIONS AND
FUR
THER DET
AILS.
W
ALL MOUNTING
Each Synergy SLX speaker can be mounted vertically or horizontally. When mounted vertically, the
wall bracket can be aligned with a wall stud (in which case the supplied drywall anchors will not be
used) or simply attached to drywall (in which case the supplied dry wall anchors will be used). When
mounting the bracket horizontally, one of the two pairs of mounting holes shown in Figure 2 to be
16" apart (holes 1 and 5 or holes 2 and 6) can be aligned with wall studs that are sixteen inches
apart. Either of the two pairs can be used. Dry wall anchors and screws should then be used in the
remaining four attachment locations. If you do not wish to mount the bracket to wall studs, all six
drywall anchors and screws must be used to attach the bracket to the wall.
To install the Synergy SLX, follow these instructions:
1. Position the mounting bracket on the wall in the desired location and orientation (vertical
or horizontal).
2. Using the mounting bracket as a template, mark the six screw locations taking care to notice the
location of wall studs. (Wall studs can be used, if desired, as stated above. However, it is not
necessary to attach the SLX bracket to wall studs.) If used in the center channel position, make
sure that the bracket is level.
3. Remove the mounting bracket and install the necessary number of supplied drywall anchors into
the wall. (Drywall anchors are not necessary in the locations where the screw will attach to a
wall stud.)
4. Route speaker wire through the mounting bracket. Wire routing channels are incorporated into
the rear of the mounting bracket. Wire can enter at any side of the bracket and will exit in the
center of the bracket directly behind the connections on the rear of the SLX as shown
in Figure 3.
5. Place the mounting bracket in the desired location and attach it to the wall by driving the
supplied screws through the bracket’s mounting holes and into the drywall anchors or wall
stud(s), making sure not to overtighten the screws.
6.
Connect the speaker wire to the SLX's binding posts.
See "Speaker to Amplifier: Keeping it
Straight" for speaker wiring information.
7.
Attach the SLX to the mounting bracket b
y sea
ting the SLX's mounting slots,
loca
ted on
each end of the back of the SLX, onto the mounting tabs of the bracket as shown in Figure 4.
The tabs will "click" into place when the connection is made. Lightly pull forward on the SLX to
make sure a solid connection has been made. To remove the SLX from the mounting bracket,
depress both buttons at each end of the back of the SLX and pull the speaker off of the mounting
bracket.
The SLX should slide of
f easil
y
. DO NOT force it. Make sure both buttons are depressed.
16"
16"
1
2
34
5
6
Figure 2
MOUNTING
SLOTS
WALL
BRACKETS
Figure 4
From Amplifier
From Amplifier
Figure 3
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Klipsch SLX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Klipsch SLX in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info