584827
6
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
CONNECTIONS AND CONTROLS
CAUTION: Ensure that the subwoofer is unplugged from the AC wall
outlet before making any connections.
“LINE IN” Connection - Most of today’s surround receivers (and
pre-amplifiers) have a line level subwoofer output labeled Subwoofer
Pre Out, Sub Out, SW Out, etc. If you have this output, connect one
end of a subwoofer cable to it and connect the other end of the cable
into the subwoofer line input labeled LEFT/LFE. This connection
allows the subwoofer to operate with both music and surround sound
movies (refer to your receiver manual). In absence of a subwoofer
output on your receiver, as an alternative hookup, you can connect
Left and Right channel Pre-Amp Outputs from your receiver (if
provided) to the Left/LFE and Right input on the subwoofer.
“LOWPASS” Control - The crossover point chosen determines
where low bass frequencies are “handed off” from the speakers to
the subwoofer. If setting the crossover point in the receiver, turn the
Lowpass Filter knob on the subwoofer to the farthest point right
(160Hz). Set the crossover point based on the size of the main left/
right speakers you are using in the system. As a general rule, for
larger, floorstanding speakers, set the crossover point between
50Hz-90Hz. If using small bookshelf or “satellite” speakers for the
mains, set the crossover point between 90Hz-150Hz. The smaller
the speaker, the higher the setting until the bass frequencies blend
well between the speakers and your subwoofer once your system is
completely hooked up. If your receiver does not have a crossover
point setting, set the Lowpass Filter on the subwoofer instead within
the same recommended settings (see receiver manual for additional
speaker setup info).
Level - If your subwoofer is connected to a Subwoofer Output of a
surround receiver, first set the subwoofer volume level control in
the receiver to the “half way” or “0 dB” position. Then increase the
volume (or gain) of the subwoofer up until the subwoofer’s volume
level matches the output of your main speakers. After this setup is
completed, the volume control on your systems main amplifier or
pre-amplifier will be the volume control for both your subwoofer and
speakers together. If your subwoofer is connected to the L/R Pre-
Amp Outputs of a receiver there will be no subwoofer volume in that
receiver to set before setting the subwoofer’s gain control.
“PHASE” 0/180 – This control is used to acoustically match the
subwoofer’s output to your main speakers. Select the position either
0˚ or 180˚ in which your subwoofer has more output at the listening
position.
Off/Auto/On – When this switch is in the “ON/AUTO” position, the
subwoofer will automatically turn “on” when it senses a signal. It will
automatically go into “standby mode” after 15-20 minutes with no
signal. When this switch is in the “OFF” position, the subwoofer will
remain “off” until the switch is manually turned back to the “ON/
AUTO” position.
Power LED indicator - Located on the front baffle, this LED indicates
the operating status of the built-in amplifier. The LED will light green
when the amplifier is on and receiving a signal. If the LED is dark
and not lit, the amplifier is off. For more information on the controls
mentioned in this manual and on bass management, see your dealer
or visit www.klipsch.com
6

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Klipsch-R-12SW

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Klipsch R-12SW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Klipsch R-12SW in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 2,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info