483687
2
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
a Tile cutter
Rip cut
Place the tile at the front edge against the front stop. (See “RIP CUT”
to the right). Position the tile so that the line to be cut is directly
over the scoring line, which is the line between the left and right
pads (See “Scoring Line” to the right). Place the table extension arms
under the tile for the best possible support. Adjust the cutting guide
by loosening the guide knob (See “Slide Rule Guide Knob to the
right) and sliding it left or right to the desired cutting position. Lock
the cutting guide into place.
Scoring line
RIP CUT
Making the cut
Place the cutting wheel on the rear edge of the tile. Slide the wheel
forward by pushing the handle down while applying medium
pressure, scoring the tile surface glaze as the handle is pushed
forward (See “SCORING” photo below). It is important to make the
cut in one continuous motion, scoring the surface only once per tile.
After scoring, and without moving the tile, position the handle so
that the breaker bar is slightly inside the front edge of the tile and
front stop. Apply increasing pressure on the handle until the tile
snaps along the score line (See “SNAPPING” photo below).
Slide rule guide
knob
Scoring
line
SNAPPING
Press down
Diagonal cuts
The cutting guide can also assist in making diagonal cuts. First,
loosen the Slide Rule guide knob so that it can move side to side
and adjust to the size of the tile you are cutting. Then loosen the
knob on the Angle Cutting guide to allow the tile to rest against the
angle guide, positioning it for a diagonal cut. Tighten both knobs.
You are now ready to make the diagonal cut.
DIAGONAL CUT
Angle cutting
guide knob
Angle cutting guide
General maintenance
1. Oil should not be used on the tile cutters. Use of oil will cause eventual gumming and sticking of the movable parts
as the oil combines with dirt and ceramic tile dust. Use a soft dry cloth to clean the rails after each use.
2. The only part routinely needing replacement is the carbide scoring wheel.
SCORING
Slide to score surface
glaze
Breaker Bar
Wear eye protection.
29605 manual.indd 2 07-11-11 13:47
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kinzo 29605 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kinzo 29605 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info