168211
5
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
5
REMOTE BASS
A
UTO
T
U
RN
ON
+12V D
C
AUDI
O
O
FFSET
L
O
HI
INP
UT
S
PKR
+
S
PKR
-
INPUT
SENSITIVIT
Y
L
X
O
VE
R
FF HI L
OU
TP
UT
L
R
R
S
PKR
+
S
PKR
-
ZXRC* REMOTE BASS
INSTALLATION
1. mount the
metal bracket
* ZXRC included with ZX750.1 ONLY
4-conductor phone cable
back view
2. slide the housing until it snaps
into the metal bracket
Input Level: The RCA inputs on KICKER ZX amplifi ers are capable of receiving either Hi or Low-level signals
from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the
Input Level switch on the amplifi er. Refer to the wiring section of this manual for additional instructions.
Crossover Switch (ZX300.1): Use the XOVER switch on the end panel of the amplifi er to set the internal
crossover to OFF or LO. When the switch is set to OFF, a full bandwidth signal will be amplifi ed. Set the switch to
LO if you want the amplifi ers internal crossover to serve as a low-pass fi lter. Never change the crossover
“OFF/LO” switch setting with the audio system on!
Crossover Control (ZX400.1, ZX500.1, ZX750.1): The variable crossover on the top of the amplifi er allows
you to adjust the crossover frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good
place to start.
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear audible distortion, then turn it
down a little.
Bass Boost Switch (ZX300.1): Turn the bass boost on to increase bass by 12db at 40 Hz. If you enable the
bass boost, it may be necessary to reduce the input gain control on the amplifi er to avoid clipping.
Bass Boost Control (ZX400.1, ZX500.1, ZX750.1): The variable bass boost control on the top of the
amplifi er is designed to give you increased output, 0–18dB, at 40 Hz. The setting for this control is subjective. If
you turn it up, you must readjust the input gain control to avoid clipping the amplifi er.
Remote Bass-ZXRC (not included with ZX300.1, ZX400.1, ZX500.1): When the crossover on your
amplifi er is set to LO pass, you have the ability to control the output level of the amplifi er remotely. To mount the
ZXRC remote bass level control, simply screw the metal bracket to the chosen location, then slide the housing
onto the bracket until it snaps into place. Run the cable from the controller to the “Remote Bass” jack on the
amplifi er chassis.
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 52011 ZX 300.1 400.1 500.1 750.1 RevC.indd 5 11/5/2010 1:22:36 PM11/5/2010 1:22:36 PM
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kicker zx 500 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kicker zx 500 1 in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info