167673
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
+
_
+
+
_
+
_
_
+12V
18"
(45cm)
24"
(60cm)
XOVER
XOVER
XOVER
Installation
1. Mounting Choose a structurally sound location to mount your Kicker amplifi er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least
4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled
passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to
mount the amplifi er.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to
the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low
level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er,
the ZX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the
source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the
RCA Inputs on the end panel of the amplifi er as shown in Figure 1. Either input method will provide a
low-level output signal at the RCA output, which effectively passes the audio signal to another amplifi er
or component. Keep the audio
signal cable away from factory wiring
harnesses and other power wiring. If
you need to cross this wiring, cross it
at a 90 degree angle.
Install a fuse within 18” (45cm) of the battery and in-line with the 8 gauge power cable connected to your
amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it.
See the fuse chart on the following page for power and ground wire size, and fusing recommendations.
3. Confi guration The following diagrams show the most common confi gurations for your Kicker ZX
series amplifi er.
ZX.2SeriesAmplifi er
Owner’sManual
Tw o ChannelModels: ZX350.2 / ZX450.2 / ZX550.2 / ZX850.2
Authorized Kicker Dealer:
Purchase Date:
Amplifi er Model Number:
Amplifi er Serial Number:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
__________________________
__________________________
__________________________
__________________________
INSTALLATION
2
ZX.2AMPLIFIER
CONFIGURATION
3
+12V
18"
(45cm)
24"
(60cm)
+12V
18"
(45cm)
24"
(60cm)
Figure 2
Figure 3
Figure 4
Minimum Impedance of 2 ohms per channel in stereo operation
Minimum impedance of 4 ohms while in bridged operation
Minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously
Ground
Remote
Turn-On
Fuse
Battery
High Pass
High Pass
Low Pass
Ground
Remote
Turn-On
Fuse
Battery
Ground
Remote
Turn-On
Fuse
Battery
Signal In
Bridge Wiring
Bridge Wiring
Bridged Operation (Mono)
Two Channel Operation (Stereo)
Stereo and Mono Operation Simultaneously (SAMS)
Note: To get the best performance from your new Kicker Amplifi er, we recommend using genuine Kicker Accessories and Wiring.
Performance
Model ZX350.2 ZX450.2 ZX550.2 ZX850.2
RMS Power in Watts, all channels driven
@14.4 Volts, 4Ω stereo, 1% THD+N
110 x 2 150 x 2 205 x 2 295 x 2
@ 2Ω stereo, 1% THD+N 175 x 2 225 x 2 275 x 2 425 x 2
@ 4Ω mono, 1% THD+N 350 450 550 850
Length: in(cm) 13 1/2 (34.2) 16 3/4 (42.5) 20 (50.7) 23 1/4 (59)
Specifi cations common to all models:
Height: in(mm) 2 1/8 (54mm)
Width: in(mm) 9 5/8 (244mm)
Frequency Response, ± 0.5 db: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95db, a-weighted, re: rated power
Input Sensitivity:
Low Level: 125mV-5V
High Level: 250mV-10V
Selectable Electronic Crossover: Variable HI, LO or OFF (bypass), 50 - 200Hz, 12db/Octave
Bass Boost: Variable 0-18db Bass Boost @ 40Hz
+
+
>
+
>
Core Cable
Ground or Shielding
High-level Speaker Output Wire
To Amplifi er
To Source Unit
Figure 1
ModelZX350.2 1 (ONE) 50 AMPERE FUSE PowerGroundWire 8GA
ModelZX450.2 1 (ONE) 60 AMPERE FUSE PowerGroundWire 4GA
ModelZX550.2 1 (ONE) 70 AMPERE FUSE PowerGroundWire 4GA
ModelZX850.2 1 (ONE) 120 AMPERE FUSE PowerGroundWire 2GA
Signal In
Signal Out
Signal In
Signal Out
Signal Out
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kicker zx 350 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kicker zx 350 2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info