159078
19
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
19
EN
ENGLISH
In case of difficulty
Resetting the Microcomputer
The microcomputer may malfunction (unit can-
not be operated, or shows an erroneous dis-
play) if the power cord is unplugged while the
power is ON, or due to some other external
factor. If this happens, execute the following
procedure to reset the microcomputer and re-
turn the unit to its normal operating condition.
Plug in the AC power cord to the wall out-
let, and within 5 seconds, press and hold
down the 7 button and press CD button.
Please note that resetting the microcomputer
will clear the contents of the memory and
return the unit to the state it was in when it
left the factory.
Check that following guide for problem resolution.
General
No sound.
\ Plug in AC cord securely.
\ Set the VOLUME control to proper
sound level.
\ Make sure the source is set to the
source you wish to operate.
\ Pull out the headphones plug from the
headphones jack.
The left and right sound outputs are reverse.
\ Check the speaker connections and
location.
The system displays features automatically.
\ Switch off the demo operation.
CD player operation
“NO DISC” is displayed.
\ Insert a disc correctly (label side up).
\ Clean the disc.
\ Use a new or readable disc.
\ Wait until the moisture condensation
at the lens has cleared.
\ Plug in AC cord securely.
Radio reception
Noise in radio.
\ Tune to a correct frequency.
\ Adjust the direction of the FM antenna.
\ AM antenna is built in; rotate the sys-
tem to face a new direction.
\ Increase the distance between the sys-
tem and TV or VCR.
Cassette deck operation
Cannot record.
\ Replace the tape or cover tabs with
adhesive tape.
\ Clean the head.
\ Use only NORMAL (IEC I) tape.
\ Do not use a cassette with more than
90-minute recording time, for the tape
used in such a cassette is very thin and
tends to cause problem such as en-
tanglement around the pinch roller or
could be easily cut off.
Timer / Clock
The timer is not working.
\ Set the correct clock.
\ Press the TIMER ON/OFF button to
switch on the timer.
\ Switch the system to standby mode.
The timer/clock is erased.
\ Power has been interrupted or power
cord has been disconnected. Set it
again.
Remote control
Does not function properly.
\ Replace the batteries.
\ Remove the obstacles.
\ Move closer to the system when us-
ing the remote control and make sure
that you are pointing at unit’s remote
sensor.
5521_08_20_EN 04.6.30, 3:22 PM19
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood hm 437 mp bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood hm 437 mp in de taal/talen: Engels als bijlage per email.

De handleiding is 0,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kenwood hm 437 mp

Kenwood hm 437 mp Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano, Espanôl - 100 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info