606707
76
Verklein
Vergroot
Pagina terug
1/77
Pagina verder
SKY CMD-2
PREPARATION FLOW
The following steps should guide you to a good start of Sky
Command operation. First connect the Transporter to the HF
transceiver.
1 <On the Commander and Transporter> Select the same VHF
and UHF frequencies.
Band A: VHF frequency Band B: UHF frequency
or
Band A: UHF frequency Band B: VHF frequency
Note: Confi gure the squelch to an appropriate level for both the VHF and
UHF band on the Commander and Transporter. If the squelch is not set to an
appropriate level, the transceivers may enter a BUSY state due to noise signals
and be unable to transmit.
2 <On the Commander> Access Menu 700 to program a
callsign (9 digits max.) for the Commander.
You may enter your exact callsign; ex. W6DJY.
3 <On the Commander> Access Menu 701 to program a
callsign (9 digits max.) for the Transporter.
This callsign must be different from the one for the Commander.
So you may add SSID characters; ex. W6DJY-1.
4 <On the Transporter> Access Menu 700 to program the same
callsign as you entered in step 2.
5 <On the Transporter> Access Menu 701 to program the same
callsign as you entered in step 3. The same callsign as you
entered in step 2.
6 <On the Commander and Transporter> Access Menu 702
and select the tone frequency.
Select the same tone frequency on both transceivers.
7 <On the Commander> Access Menu 703 and select
“COMMANDER”.
“Push [ 0 ] key to start Commander!!” appears.
8 <On the Transporter> Access Menu 703 and select
“TRANSPORTER”.
Now the Commander and Transporter are in Sky Command mode.
For operations in this mode, see “CONTROL OPERATION”. First
switch ON the HF transceiver and press [SYNC] on the Commander.
To exit the Sky Command mode, access Menu 703 and select “OFF”.
Note:
Unless you program callsigns, you cannot select “COMMANDER” or
“TRANSPORTER” using Menu 703.
On the HF transceiver, select 9600 bps and 1 stop bit (default) using the
Menu Set-up function.
Adjust the audio level on both the Transporter and HF transceiver while
listening to audio output from the Commander. An appropriate position of
the AF control on the HF transceiver might be in the range, 8:30 to 9:00.
To distinguish your various stations or nodes, you can have up to 15
Secondary Station IDentifi ers (SSIDs); ex. W6DJY-1 to W6DJY-15. You
always have to put a dash between your callsign and SSID number.
ATTENTION: Use only after verifying that there is no reception disruption
during communications.
76

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TM-D710GA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TM-D710GA in de taal/talen: Engels als bijlage per email.

De handleiding is 7,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kenwood TM-D710GA

Kenwood TM-D710GA Gebruiksaanwijzing - Nederlands - 75 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Nederlands - 55 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Deutsch - 74 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - English - 55 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Français - 77 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info