686279
169
Verklein
Vergroot
Pagina terug
1/194
Pagina verder
X8 MIG WELDER 2.5 Troubleshooting
Problem Recommended actions
The gun overheats
Make sure the coolant circulation is working normally (see
the coolant circulation warning LED in the power source).
Measure the coolant circulation speed: detach the coolant
output hose from the wire feeder while the power source
is on, and let the coolant run into a measurement cup. The
circulation must be at least 0.5 l/min.
Make sure that the welding parameters are within the range
of the welding gun and the neck. The gun and the neck have
separate limits for the maximum current; the lower one of
these is the maximum current that can be used.
The welding gun connector overheats
Make sure the connector is properly connected to the wire
feeder.
Make sure the current transfer surface and the connector pins
of the gun connector are clean and undamaged.
The gun vibrates too much during
welding
Check the tightness of the contact tip adapter and contact
tip.
Check the motor current.
Check the wire liner.
Check the filler wire. It must be straight and start coiling
when it comes out from the contact tip. If not, check the
tightness of the feeding rolls.
Gun remote control displays a warning/
error symbol
Check the Control Pad or Wire feeder control panel to see more
information about the error. For more information, see Error
codes on page 170.
Table 10: Quality of welds
Problem Recommended actions
Dirty and/or poor quality weld
Check that the shielding gas has not run out.
Check that the shielding gas flow is unobstructed.
Check that the gas type is correct for the application.
Check the polarity of the gun/electrode.
Check that the welding procedure is correct for the
application.
Varying welding performance
Check that the wire feed mechanism is adjusted properly.
Blow compressed air through the wire liner to check that it is
not blocked.
Check that the wire liner is correct for the selected wire size
and type.
Check the welding gun contact tip's size, type and wear.
Check that the welding gun is not overheating.
Check that the earth return clamp is properly attached to a
clean surface of the workpiece.
OPERATING MANUAL | EN 169
©
KEMPPI | 2018-09-28
169

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi X8 MIG Welder bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi X8 MIG Welder in de taal/talen: Engels als bijlage per email.

De handleiding is 32,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kemppi X8 MIG Welder

Kemppi X8 MIG Welder Gebruiksaanwijzing - Nederlands - 196 pagina's

Kemppi X8 MIG Welder Gebruiksaanwijzing - Deutsch - 198 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info