686279
101
Verklein
Vergroot
Pagina terug
1/194
Pagina verder
X8 MIG WELDER 2.4 Operation
4.
Use the arrow buttons to go the the parameter you want to adjust.
5.
Use the adjustment roll to change the parameter value.
Note:
The remote control is disabled if MMA or Gouging mode is selected.
Note:
For information on warning and error icons, see Error codes on page 170.
2.4.2 Preparing welding system for use
Switching on the welding system
To switch on the power source and wire feeder, turn the power source main switch to ON (I) position. When
the power source is on, the power indicator LED in the indicator panel is green.
Figure 26: Switching on the welding system
The wire feeder starts to the same operation state where it was before the last shutdown. Turn the main
switch to start and shut down the welder. Do not use the mains plug as a switch.
Note:
If the welder is left unused for a longer period, detach the mains plug to disconnect it from the
mains.
Switching on Control Pad
To switch on Control Pad, press and hold the power button for a few seconds.
Preparing cooler
Fill the coolant container inside the cooler with Kemppi coolant liquid. To weld, you must pump the coolant
through the system. Press the coolant circulation button in the front panel of the power source. It activates
the motor, which pumps the coolant to the hoses and to the welding gun.
When you press and hold the coolant circulation button, the pump begins to circulate the coolant. The line
continues to fill up automatically even if you release the button. Press the coolant circulation button again
during the automatic filling to interrupt the fill-up, for example, if any coupling is loose. If the line does not
fill up during 1 minute after the button has been released, the automatic filling stops and the indicator LED
blinks green and red in turns.
OPERATING MANUAL | EN 101
©
KEMPPI | 2018-09-28
101

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi X8 MIG Welder bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi X8 MIG Welder in de taal/talen: Engels als bijlage per email.

De handleiding is 32,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kemppi X8 MIG Welder

Kemppi X8 MIG Welder Gebruiksaanwijzing - Nederlands - 196 pagina's

Kemppi X8 MIG Welder Gebruiksaanwijzing - Deutsch - 198 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info