686279
34
Verklein
Vergroot
Pagina terug
1/194
Pagina verder
X8 MIG WELDER 2.3 Installation
2.
Pull the front panel outwards from the lower edge.
3.
Remove the lower left cover from the rear of the power source.
4.
Push the cooler inside the power source from the opening in the front.
Note:
Do not use force, but make sure the connectors on the cooler and the power source are
properly connected.
5.
Fill the coolant container with applicable coolant solution. For more information, see Filling cooler on
page 103.
6.
Attach the two screws in the front panel of the power source.
2.3.2.4 Installing or replacing mains cable
The power source is supplied with a 5-meter mains cable without a plug installed.
Warning:
The mains cable must be installed by an authorized electrician.
For high voltage versions, install the 6 mm
2
cable. For multi-voltage versions, install the 16 mm
2
cable.
The mains cable includes the following wires:
1. Brown: L1
2. Black: L2
3. Grey: L3
4. Yellow-green: Protective earth
2.3.3 Wire Feeder installation
This chapter describes the wire feeder installation.
For wire feeder cable connections, see Installing interconnection cable. For information on operating the
wire feeder, see Wire feeder control panel on page 96.
Caution:
Welding quality and efficiency are greatly dependent on the consumable parts used on the wire
line. These include the wire guide tubes, feed rolls, wire liners, gas nozzles and contact tips. Always
ensure that you are using the correct consumable parts suitable for the filler wire size and material.
For more information, visit Kemppi consumable kit selection site at kitselect.kemppi.com.
2.3.3.1 Installing wire feeder
The installation of the Wire Feeder Rotating Plate and Double Wire Feeder Rotating Plate is identical, as is
installing one or two wire feeders.
Install the wire feeder on the power source with a Wire Feeder Rotating Plate. To install two wire feeders, use
a Double Wire Feeder Rotating Plate.
Note: To set up the system for double wire feeder configuration, you need certain assembly parts.
For more information, see Double wire feeder assembly parts.
Proceed as follows:
OPERATING MANUAL | EN 34
©
KEMPPI | 2018-09-28
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi X8 MIG Welder bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi X8 MIG Welder in de taal/talen: Engels als bijlage per email.

De handleiding is 32,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kemppi X8 MIG Welder

Kemppi X8 MIG Welder Gebruiksaanwijzing - Nederlands - 196 pagina's

Kemppi X8 MIG Welder Gebruiksaanwijzing - Deutsch - 198 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info