686282
17
Verklein
Vergroot
Pagina terug
1/21
Pagina verder
17
X3 MIG Welder© Kemppi Oy 2018 1843
OPERATING MANUAL
5. TROUBLESHOOTING
Problem Cause
The machine stops
working. Overheating
indicator is lit, and Err 4 is
displayed.
The machine has overheated.
Ensure that cooling air has unrestricted ow.
The machine’s duty cycle has been exceeded.
If no other damage is caused, the fan starts working and the machine recovers
within a couple of minutes.
If the problem persists, please contact Kemppi service representative.
Machine stops working.
Err 2 or Err 3 is displayed.
The mains voltage is either too low (Err 2) or too high (Err 3). *
The machine recovers automatically, when the mains voltage is in the
recommended range (342 – 484 V).
Machine stops working.
Err 43 is displayed.
The wire feeder motor is overloaded.
Check that you are using the right wire type and that the wire feed route is
unobstructed.
Poor welding result Several factors aect the welding quality.
Check wire feed calibration.
Check that the earth return clamp is properly attached, the point of contact is
clean and that the cable and its connectors are intact.
Check the voltage and wire speed settings on the control panel are correct for the
given wire size and type.
Check that the shielding gas ow rate at the gun nozzle is correct.
Check that the shielding gas is suitable for the ller wire used.
Check that the wire feed is constant, and adjust if necessary.
Check that the mains voltage is not too irregular.
Main switch indicator does
not switch on
The machine has no mains voltage
Check the mains fuses
Check the mains cable and the wall plug
* Contact Kemppi service in case of Err 2 and Err 3 without mains voltage cause.
6. MAINTENANCE
6.1 Regular maintenance
Check regularly the electrical connections of the ma-
chine. Clean any oxidised connections, and tighten the
loosened cable connections.
Let authorised Kemppi service workshop make periodic
service to your machine. Appropriate use and regular
service guarantee trouble-free use of the machine. This
allows you to avoid interruptions and increase the pro-
ductivity of the machine.
NOTE! Remember that the machine may be repaired
only by an electrical contractor or installer authorised to
perform such operations.
6.2 Disposal of the machine
Do not dispose of electrical equipment with normal
waste!
In observance of European Directive 2002/96/EC on
waste electrical and electronic equipment, and its im-
plementation in accordance with national law, electrical
equipment that has reached the end of its life must be
collected separately and taken to an appropriate environ-
mentally responsible recycling facility.
The owner of the equipment is obliged to deliver a de-
commissioned unit to a regional collection centre, per
the instructions of local authorities or a Kemppi repre-
sentative. By applying this European Directive you will
improve the environment and human health.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi X3 MIG WELDER bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi X3 MIG WELDER in de taal/talen: Engels als bijlage per email.

De handleiding is 3,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info