686270
8
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
EN
2.6 Cable connections
Connection to the mains
The machine is tted with a 3 m long supply voltage cable and plug. Connect the supply
voltage cable to the mains. Should you need to t an alternative plug or mains cable, ensure
installation is completed by an authorised electrician.
NOTE! The fuse size needed is 16 A delayed.
If you use an extension cable, its cross-sectional area should be at least as large as the
machines supply cable (3 x 1.5 mm²). It is recommended to use 3 x 2.5 mm² extension cable.
The maximum length for the extension cable is 100 meters.
The machine can also be used with a generator. The minimum power for the generator is
4.2 kVA, and the recommended power 8.0 kVA in order for the machine to be used at
maximum capacity.
Earth return
The welding circuit earth return cable is already connected to the machine. Clean the
workpiece surface and x the earth return clamp to the work piece in order to create a
welding circuit.
Welding gun
The welding gun is already connected to the machine. The ller wire, shielding gas and
electric current is delivered to the weld inside the welding gun cable. When you press the gun
trigger, shielding gas starts to ow and ller wire feed begins. The arc ignites when the ller
wire touches the work piece. Inside the gun cable there is a factory-installed wire liner that
is best suited for welding with steel and CuSi ller wires. It can temporarily be used also with
stainless steel and aluminium wires. However, this is not recommended because of greater
friction and reduced welding performance, and it may nally lead into failure of ller wire
delivery.
If you mainly use aluminium or stainless steel ller wire, we recommend that you replace the
wire liner with a Kemppi plastic type, which is better suited for the material. For instructions
on how to change the wire liner, please refer to the Maintenance section later in this manual.
The gun neck can be rotated 360° to suit dierent welding positions. The neck is connected via
a standard clockwise screw thread. Always make sure that the neck is almost fully connected
to the bottom thread. This prevents damaging and overheating the neck.
NOTE! If you intend to use other than 0.8 mm diameter steel ller wire, change the welding gun
contact tip, gun liner, and drive roll to match the selected ller wire type and thickness.
MinarcMig Evo 170, Evo 200
6
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi MinarcMig Evo 170 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi MinarcMig Evo 170 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kemppi MinarcMig Evo 170

Kemppi MinarcMig Evo 170 Gebruiksaanwijzing - Nederlands - 26 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info