686381
17
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
EN
WiseThin, Fe group
903 1,0 Fe Ar+18%-25%CO
904 1,2 Fe Ar+18%-25%CO
913 1,0 Fe CO
²
914 1,2 Fe CO
²
WiseThin, SS group
923 1,0 SS-316 Ar+2%CO
924 1,2 SS-316 Ar+2%CO
933 1,0 SS-316 Ar+30%He+1%O
934 1,2 SS-316 Ar+30%He+1%O
Using the welding program
5. Select the welding process 1-MIG with the P9 button.
6. Press the SYNERGIC PROGRAM button to display the material group and the welding
program number. Make sure that the welding program corresponds to the ller wire and
shield gas you use.
7. Check the wire type and shield gas for the welding program in the table below.
8. Adjust the welding power with the left-hand side knob and the arc length with the right-
hand side knob.
2.2.12 SETUP features of the control panel
The machine has a number of additional features, or parameters, whose settings can be
specied with the control panel's SETUP function as follows:
1. Press and hold down the SETUP button P10 for at least 5 seconds.
2. Select the parameter to adjust using the left-hand side control knob. The parameter
name is shown in display 2.
3. Specify the parameter value with the right-hand side control knob. The selected value is
shown in the display P6. The parameter’s value is immediately stored in the memory.
4. You can exit the SETUP mode by pressing and holding down the SETUP button again for
at least 5 seconds or by briey pressing the ESC button.
All welding processes have their own SETUP parameters. For example, adjusting the post-
current for synergetic MIG welding does not aect the post-current of normal MIG welding.
The tables below show the additional features available in this welding machine and their
possible values.
Normal MIG welding parameters and their values
Name of
parameter
Name
displayed
Parameter
values
Factory setting Description
Pre Gas Time PrG 0.0 ... 9.9 s 0.0 s Pre-gas time 0 ... 9.9 s.
Post Gas Time PoG Aut, 0.1 ... 32.0 s 1,0 Post gas time,
Aut = Automatic, depending on welding
current 0.1 ... 32 s
Creep Start Level Cre 10 ... 170% 50 % Percentage of wire feed speed, 10% refers
to slow start, 170% to accelerated start
Post Current Time PoC -9 ... +9 0 Post-welding current time
15
KempArc SYN 300, 400, 500, DT 400 / © Kemppi Oy / 1117
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi Kemparc SYN 300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi Kemparc SYN 300 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info