686409
58
Verklein
Vergroot
Pagina terug
1/61
Pagina verder
58
A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
6.3.7 Cleaning the weld head
Clean weld head periodically to maintain maximum
operating eciency. Keep the unit free of moisture, debris,
and other contaminants (oil, water, abrasives, etc.) that can
aect normal operation and weld consistency.
Clean insulating components with a soft brush
and a fast drying solvent, such as acetone or
denatured alcohol.
Clean drive gear assemblies using a ne wire
brush and solvent. Inspect the drive gear, bevel
gear, and rotor assembly to insure that debris
have not damaged the rotor sprocket lobes and
aected the operation of the drive assembly. Use
a ne jeweler’s le to repair.
Clean the body with a cloth or soft brush and
solvent.
Clean the collets with ne stainless steel wool or
ne wire brush.
Only use stainless steel, as regular carbon steel will ruin
the surface passivation. All parts must be completely dry
before reassembly.
6.3.8 Internal arcing
Dirt and impurities in the weld head may cause internal
arcing. This is a situation where the arc jumps from the
tungsten electrode to the collet frame and the welding arc
fails to ignite.
When internal arcing occurs, a track of carbon is left on the
dielectric material, which may cause the same problem to
occur again.
To prevent internal arcing, do the following:
Periodically clean the weld head according to
instructions given above in section “Cleaning the
weld head”.
Maintain the tungsten electrode in good working
condition at all times.
Remember that the collet frame and collets are connected
to the ground cable and act as the ground contact for the
electrical circuit.
If internal arcing does occur, do the following:
Carefully scrape all burn marks from the plastic
body with a razor blade or other sharp scraping
tool.
Remove all carbon and polish with a ne wire
brush.
Remove all carbon o the collet frame and collets
with a ne wire brush.
Remove the rotor gear and polish if necessary
with a ne wire brush to remove any traces of
arcing.
Clean with alcohol or other suitable solvent and a
lint free cloth before reassembling.
58

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A7 TIG Orbital System 300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A7 TIG Orbital System 300 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info