686374
19
Verklein
Vergroot
Pagina terug
1/21
Pagina verder
19
Robot Gun Mount T3© Kemppi Oy 2016 1712
OPERATING MANUAL
16. REMOVING THE MOUNT
This section describes how to remove robot mount T3.
Unmounting may only be carried out by specialist personnel. Please make sure
that the shutdown procedures are strictly observed before the unmounting work
begins. Ensure this also for the components integrated into the welding system.
Risk of injury due to unexpected start-up
For the entire duration of maintenance, servicing, unmounting, and repair work, the
following instructions must be adhered to:
Switch o the power supply.
Cut o the compressed air supply.
Pull the power plug.
Removal from operation depends on the type of welding gun. Please observe the
operating instructions of the A7 MIG Gun 500-g or the A7 MIG Gun 500-w welding
guns, as appropriate.
Proceed as follows:
1. Disconnect the hose assembly from the wire feeder.
2. Open the lock ring, and unscrew the fastening screw. See Section 11.3.
3. Pull out the hose assembly.
4. Disconnect the gun neck, and remove it. See sections 11.4 and 11.5.
16.1 Disposal
For disposal, the locally applicable regulations, laws, provisions, standards, and
guidelines must be observed. For the welding torch system to be properly disposed
of, it must be unmounted rst.
16.2 Materials
This product consists for the most part of plastics, steel, and non-ferrous metals. Steel
and non-ferrous metals can be melted down, so iron products are almost innitely
recyclable. The plastic materials used are marked in preparation for appropriate
sorting of the materials for later recycling.
16.3 Consumables
Oils, greases, and cleaning agents must not contaminate the ground or enter the
sewer system. These materials must be stored, transported, and disposed of in suitable
containers. Please observe the relevant local regulations and the disposal instructions
on the safety data sheets supplied by the manufacturer of the consumables. Also,
contaminated cleaning tools (brushes, rags, etc.) must be disposed of in accordance
with the information provided by the manufacturer of the consumables.
16.4 Packaging
The shipping packaging has been reduced to a minimum. Packaging materials are
always selected with attention to their recyclability.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A7 Robot Gun Mount T3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A7 Robot Gun Mount T3 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info