686364
15
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
15
A7 MIG Gun 500-g© Kemppi Oy 2017 1712
OPERATING MANUAL
12.3.2 Shortening the wire liner
This section describes how to shorten the wire liner.
Unused wire liners or PA liners have to be shortened to
the actual length of the hose assembly.
Mounting of plastic liners is similar to mounting of
wire liners. Refer to the operating instructions of the
manufacturer of the wire feeder.
Plastic liners are used for aluminum. Plastic liners and
fastening material are available on request.
Figure 8: Shortening the wire liner
2
1
6
5
4
3
1. Support sleeve
2. Central plug
3. Hose assembly
4. Retaining nut
5. Collet chuck
6. Liner
Proceed as follows:
1. Lay out the hose assembly (3) straight.
2. Disconnect the central plug (2) from the feed unit.
3. Remove the old liner (6), and replace it with a new
one. Then insert the non-insulated side into the
central plug (2) as far as it will go.
4. Place the support sleeve (1), turned 180°, on the
new spiral liner (6) (on the side without the liner).
5. Cut o the protruding wire liner (6). The liner must
be even with the support sleeve (1).
6. Screw the collet chuck (4) onto the spiral liner (6) as
far as it will go.
The position of the wire guide can be checked
through the sight hole of the collet chuck (5).
7. Slide the collet chuck (5) and the wire liner (6) into
the central plug (2) as far as they will go.
8. Slide the support sleeve (1), with the thread side
rst, into the central plug (2), and tighten it.
9. Attach the hose assembly (3) to the central plug (2),
using the retaining nut (4).
12.3.3 Cleaning the gun neck
This section describes how to clean the gun neck.
To increase the availability time of the welding robot,
Kemppi oers an option for automated gun cleaning.
Proceed as follows:
1. Remove the gas nozzle.
2. Remove welding spatter, and spray the gas nozzle
with a suitable anti-spatter agent.
3. Check the wear parts for visible damage, and
replace any damaged parts if doing so is required.
4. Replace the equipment kit if it is worn or dirty.
5. Clean the separating point and O-rings with a
silicone-free sealing grease.
6. Check the TCP after each use and after any
collisions. Use, for example, an alignment jig to do
this.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A7 MIG gun - 500g bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A7 MIG gun - 500g in de taal/talen: Engels als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info