686377
5
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
5
A3 MIG Welder© Kemppi Oy 2018 1826
INTEGRATION GUIDE
3.3 Power source
Place the machine on a sturdy, level surface that is dry and will not allow dust or other
impurities to enter the machine´s cooling air ow. Preferably, situate the machine in a
suitable carriage unit so that it is above oor level.
The surface inclination may not exceed 15 degrees.
Ensure the free circulation of cooling air. There must be at least 20 cm of free
space in front of and behind the machine for cooling-air circulation.
Protect the machine against heavy rain and direct sunshine.
Do not operate the machine in the rain.
Never aim the spray of sparks from a grinding machine toward the equipment.
Distribution network
All regular electrical devices without special circuits generate harmonic currents into
distribution network. High rates of harmonic current may cause losses and disturbance
to some equipment.
This equipment complies with IEC 61000-3-12 provided that the short-circuit power Ssc
is greater than or equal to 4.7 MVA at the interface point between the users supply and
the public supply network. It is the responsibility of the installer or user of the equipment
to ensure, by consultation with the distribution network operator if necessary, that the
equipment is connected only to a supply with a short-circuit power Ssc greater than or
equal to 4.7 MVA.
Connecting the power source to the electric network
The A3 Power Source is connected to a 400-V three-phase network. The fuse size for 100%
load in a 400-V three-phase network with 4 x 6-mm² cable is 35 A delayed.
The machine is equipped with a ve-meter mains cable that comes without a plug. Before
use, check the mains cable and install a mains plug. If the cable does not comply with the
local electrical regulations, replace it with a compliant cable.
The mains cable or plug may be installed or replaced by only an electrical contractor or
installer authorised to perform such operations.
The power plug
The power source comes without a plug for connection to the electrical grid. Attach a
plug suitable for your power-supply standard to the power cable. Check the connections,
attach the plug to a socket, and switch the electrical power on from the welding power
source to verify that the machine works properly.
Switch the machine o and unplug it from the power socket before continuing to
further steps in the hardware installation.
If local or national regulations specify that an alternative power cable is required, the
cable must be replaced in conformity with the regulations. Connection and installation of the
power cable and plug should be carried out only by a suitably qualied person.
If changing the power cable, take the following facts into consideration:
The cable enters the machine through the inlet ring on the rear panel and is
fastened in place with a cable clamp (05). The cover plate of the power source
must be removed to access the electrical cable connector.
The phase conductors of the cable are coupled to connectors L1, L2, and L3.
The protective ground line, colored green and yellow, is coupled to the marked
connector.
If you are using ve-lead cable, do not connect the neutral conductor.
05
*
L3
L2
L1
* In S-type cables there is a protective grounding conductor, green-and-yellow striped.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A3 MIG Welder bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A3 MIG Welder in de taal/talen: Engels als bijlage per email.

De handleiding is 2,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info