598226
123
Verklein
Vergroot
Pagina terug
1/256
Pagina verder
*OPC — Operation Complete Set the OPC bit in the standard event status register after
all pending commands are complete
Description
On power-up or when the *CLS or *RST is executed, the Model 2000 goes into the Op-
eration Complete Command Idle State (OCIS). In this state, no pending overlapped com-
mands exist. The Model 2000 has three overlapped commands:
:INITiate
:INITiate:CONTinuous ON
•*TRG
When you send the *OPC command, the Model 2000 exits from OCIS and enters the Op-
eration Complete Command Active State (OCAS). In OCAS, the instrument continuously
monitors the No-Operation-Pending flag. After the last pending overlapped command is
completed (No-Operation- Pending flag set to true), the Operation Complete (OPC) bit in the
Standard Event Status Register sets, and the instrument goes back into OCIS.
Note that the instrument always goes into OCAS when *OPC is executed. If no pending
command operations are present (e.g. trigger model in idle state), the Model 2000 immedi
-
ately sets the OPC bit and returns to OCIS.
When used with the :INITiate or :INITiate:CONTinuous ON command, the OPC bit of the
Standard Event Status Register will not set until the Model 2000 goes back into the idle state.
The initiate operations are not considered finished until the instrument goes into idle.
When used with the *TRG command, the OPC bit will not set until the operations associ-
ated with the *TRG command (and the initiate command) are finished. The *TRG command
is considered to be finished when the Device Action completes or when operation stops a
control source to wait for an event (see Trigger Model in this section).
To use the *OPC exclusively with the *TRG command, first force the completion of the
initiate command so that only the *TRG command is pending. Do this by sending the :ABORt
command to place the instrument in idle, which (by definition) completes the initiate com-
mand. Since continuous initiation is on, operation continues on into the Trigger Model. After
sending the *TRG command, the OPC bit sets when the *TRG command is finished.
2000-900 (J - Aug 2010) BOOK.fm Page 44 Wednesday, October 12, 2011 12:29 PM
123

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Keithley 2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Keithley 2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Keithley 2000

Keithley 2000 Gebruiksaanwijzing - Deutsch - 122 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info