522389
4
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
from the inside (the cylinder side). Because this may damage the seals, do it only if the seals are
to be replaced.
3. Remove the piston seals from the piston.
4. Grasp the outside of the cylinder and pull it out of the pump back (if tight, rock it from side to side
while pulling). Yo7 may need to use a large channel-lock pliers for additional leverage.
5. Remove the O-ring and back-up washer from each end of the cylinder.
6. Using a small-diameter screwdriver, or a paper clip or similar wire, push through the side hole in
the pump body back to remove the plug as shown in the illustration.
REASSEMBLY
NOTE: For the following reassembly steps, refer to the appropriate illustration next to the disassembly
procedure, and to page 9.
IMPORTANT: Clean all components before reassembly.
IMPORTANT: Lubricate all O-rings and seals with silicone lubricant when the components are
reassembled. Do not use any petroleum-based grease or oil (including petroleum jelly) as they will
degrade the membrane.
Reinstall Piston and Cylinder in Pump Back (PowerSurvivor-35)
1. Install a new O-ring and back-up washer on each end of the cylinder, as shown in the illustration.
The curbed side of the washer must face the O-
ring.
INSTALLING SEALS ON CYLINDER
Install the cylinder into the pump back. Guide it
carefully into place so that the back-up washers don’t
“roll”.
Install the two new piston seals on the head of the
piston, with their smooth surfaces back-to-back.
Install the piston assembly into the pump body
back. Then slide the rod seals (open end first, as
shown on the next illustration) down the plunger
rod and into the pump body back. Be careful that you
don’t invert the rod seals while installing (guide them
into place with your fingers).
Slide the back-up washer and then the rod bushing
down the plunger rod. Press the rod bushing all the
way into the pump back so that itt is flush with the
opening.
NOTE: On a Survivor-35, reinstall the pin into the hole in
the piston rod.
Push the pump back plug into the hole where the old one
was removed.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Katadyn REPAIR SEAL KIT Survivor 35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Katadyn REPAIR SEAL KIT Survivor 35 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info