522385
2
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
Disassembly:
1. Before beginning disassembly, run the watermaker and stop it when the piston shaft is at its
farthest point of travel away from the pump (toward the drive assembly). This provides enough
room for sliding the rubber boot
back toward the pump in Step 3.
2. Use the 11/16" open-end wrench
to disconnect the two high-
pressure hoses (coming from the
membrane housing) from the tube
connectors on the check valve
plate and the valve assembly.
Loosen the hose clamps and
remove the reinforced plastic
seawater intake and reject brine
hoses. See Figure R-1.
3. Use the 1/2" open-end wrench to
remove the four hex nuts securing
the pump back plate to the drive
assembly. Then pull the pump
away from the drive assembly to expose as much of the piston shaft as possible. Slide the black
rubber boot on the piston shaft toward the pump to expose the shaft coupling pin. Use a small
screwdriver or allen wrench to push the coupling pin out of the shaft. (Note: the coupling pin is a
loose fit and may fall out on its own.
Do not lose it.) Separate the pump
from the drive assembly and set the
drive assembly aside in a safe place.
Slide the black rubber boot off the
piston shaft. Move the pump to a
clean work surface for further
disassembly. See Figure R-2.
4. Remove the plastic intake hose barb
from the check valve plate. While
the pump is still bolted together, use
the 7/8" open-end wrench to just
loosen the tube fitting in the check
valve plate. Then use the 1/4" allen
wrench to remove the six sockethead
flange bolts that hold the check valve
plate to the pump body. Separate
the check valve plate from the pump
body and remove the large o-ring
(8012830) seal between them. See Figure R-2.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Katadyn REPAIR SEAL KIT PowerSurvivor 80E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Katadyn REPAIR SEAL KIT PowerSurvivor 80E in de taal/talen: Engels als bijlage per email.

De handleiding is 0,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info