522383
4
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
Reassembly: Before you begin reassembly of the watermaker, clean all parts using clean, lint-free
rags. At this time, all parts should be carefully inspected for wear or damage. Use a 10x magnifier or
loupe to examine the seals, o-rings and other small parts. Stubborn rust stains and deposits on metal
parts may be cleaned with a soft-metal wirebrush (e.g., stainless steel or brass). Do not use polishes,
cleaning compounds containing abrasive materials, or regular steel wire brushes. Refer to the exploded
drawing of the pump in Figure A-2 in the Appendix for the location of parts and seals during
reassembly. Refer to Figures A-3 and A-4 in the Appendix for full-size drawings and identification of
the components included in the Repair Seal Kit. In the following procedure, references to the Repair
Seal Kit will be abbreviated to RSK.” It will be assumed that all o-rings, seals, and mating surfaces
have been lightly lubricated with non-petroleum silicon grease (supplied with the RSK).
Warning: Use only non-petroleum silicon grease to lubricate your watermaker parts. Lubricants
with a petroleum base will damage several watermaker components, including the reverse osmosis
membrane. Be especially cautious of lubricants that “contain” teflon, silicon, etc.such products
could also contain petroleum-based components. An ample supply of silicon grease is included with
each RSK.
Reinstall the piston: If you want to replace the O-rings on
the piston, refer to the figure below
Install washer with chamfer on washer
facing ½ dia of plunger rod and a new
O-ring onto the plunger rod, if you have
an old-style piston, you only have to
install a new O-ring into the plunger rod
without a washer.
Slide piston onto the threaded end of the
plunger rod, and secure with the washer
and nut.
1. Refer to Figure R-5 during the following procedure.
Place the piston assembly on a flat, stable surface with
the shaft pointing up. Slide the installation tool
(provided in the RSK) over the piston shaft with the wide
end down. Lubricate the new PIP ring, cup seal and the installation tool with silicon grease. With
the grooved side facing up, slide the PIP ring down the installation tool and onto the piston. Re-
peat this process for the cup
seal. Note that the grooved
side of the cup seal should be
facing down; i.e., the grooved
sides of the PIP ring and the
cup seal should be facing each
other. When finished with the
installation, remove the instal-
lation tool from the piston shaft.
2. To install the check valve
components, refer to Figure R-
3. Remove the old o-rings from
the poppet valves and valve
seats and install new o-rings from the RSK. Observe that the hole in the center of each valve seat
has a beveled edge on one side. Use your finger to press a valve seat into the bore for the reject
check valve assembly. The seat should be pressed all the way in, with the beveled side of the valve
facing outward (that is, against the end of your finger). Use the same technique to install the other
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Katadyn REPAIR SEAL KIT PowerSurvivor 160E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Katadyn REPAIR SEAL KIT PowerSurvivor 160E in de taal/talen: Engels als bijlage per email.

De handleiding is 0,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info