3
Vibration Unit Battery Installation
The vibration unit requires one (1) C alkaline battery (not included).
1. Using a crosshead screwdriver, open the battery compartment located
on the bottom of the unit (Fig. 13).
2. Insert one (1) alkaline battery.
3. Using the crosshead screwdriver, securely replace the battery
compartment cover.
Please note: Batteries may leak uid that can be harmful to your baby and
the product. We strongly recommend using only high-quality alkaline (dry)
batteries.
Operating Vibration Unit
1. Turn the switch to the “ON” position to begin gentle vibrations of the
bouncer (Fig. 14).
2. Turn the switch to the “OFF” position to stop vibrations.
Securing Baby in Bouncer
1. Open the activity arches away from each other and place baby in the
seat. Position the safety restraint belt between the baby’s legs (Fig. 15).
2. Fasten the two ends of the safety restraint belt to their corresponding
buckles until you hear a click. Make sure the safety belt is securely
attached by gently pulling it away from your baby.
3. Adjust the activity arch to an appropriate angle for your baby. Turn on
vibration unit and Lights & Music Crab, if desired.
Reclining Mechanism
Press the knobs as indicated in Fig. 16 in order to adjust the bouncer to a
reclining or sitting position.
Note: You must press both knobs and turn at the same time (Fig. 16).
Cleaning & Storage
1. The seat pad is the only machine washable part. Wash it separately in
cold water on the gentle cycle. Do not use bleach. Do not tumble dry.
Do not dry clean.
2. All other parts – wipe down with a damp cloth and allow to air dry. Do
not immerse in water.
3. Remove the batteries for long-term storage or periods of non-use.
And Don’t Forget These Safety Rules:
Batteries should be replaced by adults only.r
Do not mix old and new batteries.r
Non-rechargeable batteries are not to be recharged.r
Rechargeable batteries are to be removed fromr the mobile before
being charged.
Rechargeable batteries are only to be chargedr under adult
supervision.
Do not mix alkaline, standard (carbon-zinc) orr rechargeable (nickel-
cadmium) batteries.
Exhausted batteries are to be removed from ther toy.
Do not burn batteries. Dispose of batteries in ar safe and appropriate
manner.
Use only batteries of the same or equivalent typer as recommended.
Batteries are to be inserted with the correct polarity.r
The supply terminals are not to be short-circuited.r
For Your Child’s Safety: Do not modify or alter this product in any way.
Product Assembly
Assembling Bouncer
Product assembly requires a Phillips screwdriver.
1. Attach the two wire base frames to the base tube as shown in the
illustration. Make sure the rounded side of the base tube is arched
outward (Fig. 1).
2. Line up the holes at the end of each side of the base tube with the holes
at the side of the anti-skid feet (Fig. 2).
3. Fit the screw through the hole located at the side of one of the anti-skid
feet and tighten with a crosshead screwdriver. Make sure you repeat for
both ends of the base tube (Fig. 3).
4. Insert the headrest tube into the end of the reclining mechanism on the
wire base frame to form a continuous arch until a click indicates that the
two sections are locked (Fig. 4).
5. Insert the foot rest tube into the end of the reclining mechanism on the
wire base frame to form a continuous arch until a click indicates that the
two sections are locked. Make sure that the arch connectors are facing
up (Fig. 5).
Note: Be sure to check that both sides are secure and that all parts of the
base are securely connected before proceeding.
6. Place the seat pad over the frame starting at the headrest. Guide the arch
connectors through the openings in the fabric. Make sure the seat pad
covers the entire frame (Fig. 6).
7. Fasten the safety buckle underneath the seat pad (Fig. 7).
Mounting Activity Arch
1. Insert the ends of the activity arch into the arch connectors until a click
indicates that each is locked in place (Fig. 8).
2. Attach toys by connecting the plastic rings through the fabric loops on
the arches.
3. To release activity arch: press the button on the bottom of the arch and
gently pull the arch upwards. Make sure to press and pull at the same
time (Fig. 9).
4. Never use the activity arches to carry the bouncer.
Lights & Music Crab Battery Installation
The lights and music crab requires three (3) AAA alkaline batteries
(not included).
1. Using a crosshead screwdriver, open the battery compartment located
on the upper side of the crab (Fig. 10, Fig. 11).
2. Insert (3) AAA alkaline batteries into the battery compartment.
3. Securely replace the battery compartment cover and using the crosshead
screwdriver, tighten the screws.
Operating Lights & Music Crab
Clip the crab directly onto the activity arch.
Note: You may angle the position of the crab by attaching it to one or both arches.
Select the operating setting on top of the crab (Fig. 12).
1. Choose one of 2 play settings:
Parent activated r – for continuous play: lights & music entertain
baby for 15 minutes.
Baby activated – Baby initiates short bursts of music and r
watches corresponding lights action.
2. Each setting may be set to either:
Music and lights moder
Mute mode (lights only) for quiet playr
3. Manually turn the switch to “O” at the end of play.
Pull out the head rest tube from the seat pad and continue to
assemble the product according to the instructions (Fig. A,B,C).
© 2011. All rights reserved, Tiny Love Ltd.
For more developmental information and playing tips please visit:
www.tinylove.com
