166238
11
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
11
®
XA4100
Troubleshooting
Problem Possible Cause Corrective Action
Amplifier does not operate
(power LED not on) when
vehicle and radio are on
Radio volume needs to be
turned up too high for amp
to work
Radio volume is too sensitive
Sound from only one speaker
Sound distorted
Blows fuses
Alternator whine in outputs
(vehicle ignition noise)
Loud pop in speakers when
power is turned on or off
Protect light comes on/
amplifier shuts down
No output on channels
Can’t find cause of problem
No power to +12V terminal
No power to remote wire with radio on
Fuse blown
Input level control (gain control)
adjusted too low
Input level control adjusted too high
Defective speaker
Poor connections to speaker (wire)
Speaker wires shorting together
RCA input cable defective
Input level control adjusted too high
Speaker wires shorting together
Power wires hooked up incorrectly
Speakers blown or defective
Radio has poor noise immunity
Improper ground connections
Remote wire (blue) not properly
connected
Amp is in thermal protection
Faulty speaker connection and/or
crossover
Low battery voltage
Speaker impedance less than 2 ohms
per channel
Speaker wires not connected to
speakers properly
Input hooked up incorrectly
Repair wire or connections
Check connections to radio with test light
Check fuse
Adjust input level control (gain control)
Adjust input level control to lower setting
Replace speaker
Check connections
Separate speaker wires and insulate
Replace cable
Adjust input level control
Separate speaker wires and insulate
Check power wire connections
Check speakers
Disconnect audio inputs to amplifier – if noise disappears
then the radio is at fault
Make sure radio and amplifier are grounded to the same point
Refer to page 4 for proper installation. If radio does not have a
power antenna lead and you have connected the remote lead to
an ignition source then you may get a “pop” in your speakers.
This is not uncommon. You may have to put a switch in line with
the remote lead to turn the amp on/off manually.
Let amp cool down before attempting to turn back on (some
installations may require a fan to keep the amp cool, especially if
you are driving subwoofers with the amp)
Check speakers and/or crossovers for loose or bad connections
Make sure you are getting between 10.8-15.6 volts to the
amplifier with a digital multimeter measured at the amplifier
If you are using 4 ohm speakers you cannot have more than two
speakers wired in parallel per channel Amp will not operate
into 2 ohms bridged
Refer to pages 5, 6 and 7 for proper installation
Contact Jensen Technical Assistance (1-800-323-0221)
5313Eamp.p65 4/10/99, 7:05 PM11
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jensen xa 4100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jensen xa 4100 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info