509190
1
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
Figure A
Introduction
Thank you for choosing a Jensen product.
The JWR200 Marine Wired Remote Control
allows you to control basic functions of
Jensen Marine JMS series radios, including
power, mode, volume, tuning and CD, iPod
and satellite radio operation.
Installation
1. Choose a mounting location on the
instrument panel that will allow enough
room behind the panel to run the wired
remote cables to the existing radio.
2. Cut a hole in the instrument panel using
the supplied template. At least 2 ½" depth
is needed to mount the remote control.
Important: Do not mount unit where it
can be submerged or subjected to high
pressure spray.
3. Insert the remote control into the hole and
then secure from the other side using the
threaded ring, illustrated in Figure A.
Wiring
Once the remote has been mounted, route the
cable from the remote and connect the cable
to the radio. Note the connector polarity on
the extension cable. The 18 foot extension
cable may be used to connect the remote to
the radio. Up to two additional extension
cables (JWREXT) may be purchased and
used to extend the reach of the remote up to
54 feet. Important: When connecting the
cables, be sure to route the extension cable
away from sharp objects, corners, and places
where it might get pinched, as this could
affect performance and cause damage to the
unit. Up to two more remote controls can be
added with a "Y" cable adapter
(JWRYCBLS).
Introducción
Gracias por seleccionar un producto de
Jensen. El control remoto atado con alambre
marina JWR200 permite que usted controle
funciones básicas de las radios de marina
JMS de Jensen, incluyendo energía, modo,
volumen, iPod, del CD y la operación de
radio del satélite.
Instalación
1. Seleccione una localización del montaje
en el tablero de instrumentos que
permitirá bastante sitio detrás del panel de
funcionar los cables alejados atados con
alambre a la radio existente.
2. Corte un agujero en el tablero de
instrumentos usando la plantilla provista.
Profundidad por lo menos del la 2 1/2 " es
necesaria montar el control remoto.
Importante: No arme la unidad en un
lugar donde se pueda hundir o sujetado al
aerosol de alta presión.
3. Inserte el control remoto en el agujero y
después asegúrelo del otro lado usando el
anillo roscado, ilustrado en la Figure A.
Cableado
El remote controlo se ha montado, encamina
el cable del remote controlo y conecta una
vez el cable con la radio. Observe la
polaridad del conectador en el cable de la
extensión. El cable de la extensión de 18 pies
se puede utilizar para conectar el remote
controlo con la radio. Hasta dos cables
adicionales de la extensión (JWREXT) se
pueden comprar y utilizar para prolongar el
alcance del remote controlo hasta 54 pies.
Importante: Al conectar los cables, sea seguro
encaminar el cable de la extensión lejos de
objetos, de esquinas, y de los lugares agudos
en donde puede ser que consiga pellizcado,
pues éste podría afectar funcionamiento y
causar daño a la unidad. Hasta dos mandos
más a distancia se pueden agregar con un
adaptador del cable de "Y" (JWRYCBLS).
Introduction
Merci d'avoir choisi un produit Jensen. La
télécommande branchée Marine JWR200
vous permet de contrôler les fonctions de
base des radios marines JMS Jensen, y
compris la puissance, la mode, le volume, la
syntonisation et l'opération CD, iPod et radio
satellite.
Installation
1. Choisissez un emplacement de montage
sur le panneau d'instruments qui vous
laissera assez de place derrière le panneau
pour brancher les câbles à distance à la
radio existante.
2. Faites un trou dans le panneau
d'instrument en utilisant le modèle fourni.
Une profondeur d'au moins 2 1/2'' est
exigé pour monter la télécommande.
Important : Ne montez pas l'appareil là où
il peut être submergé ou est exposé à des
embruns de haute pression.
3. Insérez la télécommande dans le trou et
puis l'attacher de l'autre côté en utilisant la
bague filetée, comme illustré dans la
Figure A.
Câblage
Lorsque vous avez fini de monter la
télécommande, faites traverser le câble depuis
la télécommande et branchez le câble à la
radio. Le câble d'extension de 18 pieds peut
être utilisé pour brancher la télécommande à
la radio. Vous pouvez acheter jusqu'à deux
câbles d'extension (JWREXT) pour étendre la
portée de la télécommande jusqu'à 54 pieds.
Lorsque vous branchez les câbles, assurez-
vous que vous faites traverser le câble loin
des objets fins, des coins et des endroits où il
peut être pincé, comme cela peut avoir un
effet sur la performance et endommager
l'appareil. Jusqu'à deux télécommandes
peuvent être ajoutées avec un adapteur de
câble d'Y (JWRYCBLS).
JWR200 Wired Remote
Installation Instructions
www.asaelectronics.com © 2010
POWER
JWR200
MODE
ENTER
CAT
DISP
VOL+
UP
VOL-
DN
BAND
WB
MUTE
>
>>
>>
Power
Potencia
Alimentation
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jensen JWR200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jensen JWR200 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info