616090
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Placement
Make certain the speaker is located between wall studs to avoid cutting into studs. Place the
supplied template a minimum of 5/8 from any studs. Level it and draw a line around it to mark
the cutout. Take care when cutting the hole to avoid cutting into pipes or electrical conduits. If
you encounter pipes, electrical conduits or other obstacles you may have to select another
location for the speaker.
Installation
First install the frame. Loosen screws A (fig. 1) by turning them counter clockwise. Loosen all 4
screws until the Dog ears B (fig. 2) can move freely. Do not remove the screws. Install the frame
into the wall and level it (notice TWEETER and WOOFER markings on the frame). Turn screws A
clockwise until they are tightened and the frame is firmly installed.
Next install the speaker into the frame. Before installing the speaker connect the speaker wires
as described under Hookup and set the impedance switch to the desired position (see
Adjustments). Remove the grill from the speaker. Place the speaker into the frame and secure
with the 6 screws supplied.
Before reinstalling the grill on the speaker make tweeter level adjustments as described under
Adjustments. Reinstall the grill. If the grill has a loose fit and/or is vibrating when the speaker is
playing remove the grill, install the supplied non-curing glue strips at locations C (fig. 1) and
reinstall the grill.
Hookup
The receiver/amplifier must be turned OFF before you connect the speaker or it may cause dam-
age to the amplifier.
Connect the speaker wires from the receiver/amplifier to the speakers. When connecting the
speaker wires make sure that LEFT (L) is connected to LEFT (L), RIGHT (R) to RIGHT (R), POSITIVE
(+) to POSITIVE (+) and NEGATIVE (-) to NEGATIVE (-). If terminals are color coded, RED is POSI-
TIVE (+) and BLACK is NEGATIVE (-).
Adjustments
The tweeter can be tilted towards the listening area, due to high frequencies being more
directional than low frequencies. The impedance of the speaker and the level of the tweeter are
adjustable.
IMPEDANCE:
Located on the crossover on the back. The factory setting is 8 ohm. If the
receiver/amplifier specifies a minimum impedance of 4 ohm, the speaker
may be switched to the 4 ohm position. This will make the speaker play
louder. When installing more then 1 pair of speakers to a receiver/amplifier
special care should be taken to impedance matching the speakers to the
receiver/amplifier. This may require impedance matching devices. Con-
sult your dealer for information regarding impedance matching.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jamo 660CS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jamo 660CS in de taal/talen: Engels als bijlage per email.

De handleiding is 3,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info