554881
4
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
GC-61 GSM communicator 4 / 4 MHZ51105
7. A brief list of programming instructions
8. Wiring diagram for the GC-61 – Security grade 3
Fig. 2 shows the wiring diagram for the GC-61, which is connected to a control panel. The GSM simulated line is the primary communication link with a
telephone line serving as a backup using the AUX output (see the chapter 2.15). The system checks the connection between the GC-61 and the control
panel by means of the tamper wiring. In addition the telephone line is balanced by a 10 k resistor. The resistor is attached to the PHONE terminal.
Figure. 2
Function Sequence Available setting Default setting
APN setting for GPRS
communication
GPRS
xxx,yyy,zzz,
xxx is the APN, yyy is a user name, zzz is a password Internet
Service access code PG0 xxxxxxxx xxxxxxxx is the code, 8 digits maximum 0000
ARC main telephone PG1p xxxxx
Erased
ARC back up telephone number PG2p xxxxx
p =1 for ARC1, p =2 for ARC2
xxxx = tel. number (max. 20 digits) or
a # followed by an IP address plus port which must be
specified by exactly 4x3 + 5 = 17 digits using zeros for left-
hand bit stuffing, e.g. PG11#12304506708908080
Erased
Account ID PG3p zzzz
p =1 for ARC1, p =2 for ARC2
zzzz is the account ID, 8 digits maximum
Erased
Selecting the ID number PG94 x
x=0 the ID number of the GC-61 is used for alarm system
identification.
x=1 the ID number of the attached landline communicator
is used for alarm system identification.
the ID number of the
GC-61 is used
Communication format PG4p x
p =1 for ARC1, p =2 for ARC2
x=0…Contact ID, x=1...Jablotron SMS, x=2...Jablotron
GPRS
Jablotron GPRS
ARC Report switch PG5p y
p =1 for ARC1, p =2 for ARC2
y=0... report is disabled, y=1...report is enabled
y=0
Use ARC2 as a backup of ARC1 PG62 y
y=0...two independent ARCs, y=1...ARC2 is backup for
ARC1
y=0
ARC redialling pause PG7p t p=1 ARC1, p=2 ARC2
t=1 to 9 (x 5minutes)
5 minutes
ARC connection surveillance report
frequency
07 p hh mm p=1 ARC1, p=2 ARC2
hh mm = hours minutes, 9999=24hr. after last report
24hr. after the last
report
INP input CID code setting PG-91 xxxyyzzz
xxx is a report code, yy is the number of the subsystem,
zzz is the event source
Erased
Phone number prefix setting PG-92 xx xx is the phone number prefix “+”
AUX switch control AUXON, AUXOFF
AUXON switches the AUX output on, AUXOFF switches
the AUX output off
-
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron GC-61 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron GC-61 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info