554982
2
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
CU-07 Tracer unit 2/2 MKW51102
parts of this unit are initialized during these approx. 2 minutes of
flashing. If the unit is connected to the power supply for the first
time after its purchase, the slow flashing changes to rapid
flashing after the two minutes, indicating that the unit is waiting
for configuration. When the unit has received its configuration
(from your tracer service provider) it sends a confirmatory SMS
reporting the successful setting to the number from which it was
configured. The unit is now ready for journey recording
Solving problems which might occur during primary
configuration:
I have not received a confirmatory SMS, even though the
whole process was carried out in conformity with the
instructions. Solution: try to repeat the process.
The unit’s LED indicator has started flashing SOS in Morse
code (3 dots, 3 dashes, 3 dots). Solution: a unit or SIM card
failure has been detected, contact the tracer service provider.
2. Advanced unit configuration
Advanced unit configuration increases the convenience
and functionality of the whole monitoring system. The
configuration can be carried out via SMS messages sent to
the unit’s telephone number.
Each SMS must begin with a six-digit number (the default
number is 123456). The manufacturer recommends
changing this password, see 2.1. The password should be
followed with a comma and then one or more commands
separated with other commas. The SMS must not exceed 160
characters.
2.1. Access password change
The manufacturer recommends changing the password. Be
careful when changing the password; if you forget it, it is
impossible to restart the unit to default settings. In such a
case contact the manufacturer.
Command format: Password,MCxxxxxxxxxxxx
where: xxxxxx is a new access password for the device
(the 6 characters should be repeated twice, only digits
can be entered)
Command example:
123456,MC654321654321 (the new password will be 654321)
2.2. Entering drivers’ telephone numbers
If the unit is installed in a vehicle which is used by multiple
drivers, it is possible to set the number of the driver who is going
to drive the vehicle easily by dialling into the unit from the
driver’s telephone. The device memory can hold telephone
numbers of up to 15 drivers who can identify themselves by
dialling into the unit. The telephone number can consist of 12
digits maximum and it must be entered in the international
format.
Command format: Password,TELx+yyyyyyyyyyyy
where: x – the unit’s reference number of the telephone
number (from 1 to 15);
yyyyyyyyyyyy – telephone number in international
format (max.12 digits excluding the «+» sign)
Example of a command programming numbers of drivers 1 and
2: 123456,TEL1+420608234567,TEL2+420777654321
Format of the command to erase a telephone number:
Password,TELx+0
Example of a command to erase driver 1’s telephone number:
123456,TEL1+0
Note: One SMS can contain multiple commands; the password
is only stated at the beginning of the SMS.
2.3. Driver selection by dialling in
A driver can assign himself to a journey by dialling into the unit
from his telephone if his number is recorded in the unit’s
memory (see 2.2). The unit terminates the call automatically and
the driver who has called into the unit is set for all the following
journeys until another driver dials in.
2.4. Driver selection by an SMS command
A driver can also be selected with an SMS command (e.g. a
function for a dispatcher). In order to change the current driver’s
number you have to enter the following command:
Command format: Password,Dxx
where: xx – the two-digit number of a driver (01 to 15)
Command example:
123456,D02 (to set driver 2)
2.5. Journey type setting
If you need to differentiate between various journey types
(private, business, etc.), you can set it before the
commencement of a journey by sending an SMS. The device
enables classification into five journey types. The current
journey type can be selected by sending an SMS command.
The journey type can be changed via an SMS command
without a password, but only from telephone numbers
recorded in the unit (see 2.2.). In such a case the driver’s
number changes automatically together with the journey type.
Command format: Tхх
where: хх – journey type:
00 = business (default)
01 = private
02 = service
03 = foreign business (e.g. due to the price of fuel)
03 = foreign personal (e.g. due to the price of fuel)
Command example:
T01 (sets a private journey) and the driver
is changed according to the telephone number from which the
command was sent.
The journey type can also be changed using an SMS
command with a password. In such a case only the journey
type changes - the driver remains unchanged. This command
can also be sent from telephone numbers which are not
recorded in the given unit (function suitable e.g. for a
dispatcher).
Command format: Password,Tхх
where: хх – journey type (see above)
Command example:
123456,T01 (sets a private journey)
2.6. Journey termination timer setting
The device enables the setting of the time interval necessary for
journey termination. If we set the timer to 600 sec., then the unit
waits for vehicle motion detection for 10 minutes after the
journey termination. If the vehicle starts moving again, the
original journey continues. Otherwise the journey is terminated
and the unit switches to sleep mode.
Command format: Password,ETх
where х – number of seconds
permitted values: 200 s. - 5100 s. (85 min.)
default setting 300 s. (5 min.)
Command example: 123456,ET600 (time-out set for 10 min.)
2.7. SMS command reception confirmation
The device can confirm execution of the received SMS
commands based on the following parameter setting:
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CU-07 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CU-07 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info