554993
6
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
2322
ENEN
MZZ56200MZZ56200
INSTALLING THE CAMERA
1. Carefully unpack the camera and remove the foil on IR LED cover.
2. Mount the camera on a wall
Mark the position of the screw holes on the wall, drill the holes and
screw 2 screws into them, then rmly attach the camera to the
wall by placing the stand over the installed screws and pushing the
base downwards.
NOTE: The camera can also be simply placed on a flat surface
without any special installation needed.
3. Adjust the camera to monitor the requested area.
CONNECTING THE CAMERA TO THE POWER
The camera can be powered either by the provided power adaptor or using the included rechargeable
accumulator (or 4 AA batteries, not included).
NOTE: If you plan to permanently mount the camera on a wall location, it is recommended to use the
included camera power adaptor to prevent interruptions to the image, as using battery power is only
intended as a temporary power solution.
Power Adaptor
Connect the power adaptor to the camera. Make sure the power adaptor is plugged into an outlet.
Rechargeable Accumulator
1. Remove the battery cover from the
base of the camera.
2. Insert the included rechargeable
accumulator into the battery
compartment. Make sure to
correctly line up the positive (+)
and negative (-) terminals of the
accumulator.
3. Put the battery cover back on.
NOTE: If the camera is connected to
the AC adaptor, the batteries will not
be used, although the accumulator
would be recharged. The accumulator
is intended for short term usage
only.
Connect the 9V adaptor to the Power
Input on the back side of the camera
VIEWING MODE
1. Signal Indicator –shows the strength of the signal being received from the camera. The number of
bars in the signal indicator shows the strength of the signal.
Signal Strength Indicator Warning
Perfect None
Good Nove
Fair Low Signal
Low Low Signal
No Signal No Signal
2. Channel Indicator – Displays the current channel
number. Press the RIGHT arrow on the receiver
to switch between available cameras.
Note: This option is not available for the Tiny mo-
nitor.
LOW SIGNAL AND NO SIGNAL WARNINGS
When the receiver is positioned too far from the camera, the following warning messages are displayed:
LOW SIGNAL: The "LOW SIGNAL" appears
when the receiver has one or two bars. You will
still get an image, however updating may be
less frequent.
NO SIGNAL: The "NO SIGNAL" message
means the receiver cannot access the camera.
Please reposition the camera, or check the
camera power.
Position the base holes over the
screws. Slide the base down to lock
the base in place.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CMD6129S Tiny bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CMD6129S Tiny in de taal/talen: Engels als bijlage per email.

De handleiding is 9,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info