555008
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Remote control for central locking CL-301SL 2/4 MCK51104 Remote control for central locking CL-301SL 3/4 MCK51104
Installation: Examine the central locking system of your car and identify the necessary signals of the
car wire harness at first. Disconnect the battery before starting the installation. Keep in mind that if your
car has memory functions, they may be erased if you disconnect the battery. Refer to the car owners'
manual before disconnecting the battery. The lock signal can also be used for automatic closing of
powered windows.
Wiring:
White/blue = unlock output, white/black = lock output. These outputs provide signals to control the door
lock system. The maximum output current for either of these wires is 200mA ( NPN transistors switching
to the GND). Connect these wires to the corresponding inputs of the control unit of the locking system. If
the control unit is not equipped with extra inputs for remote control, you can connect the output wires of
the CL-301SL to inputs for position sensors of the front door actuators.
See "Examples of CL-301SL use for different central locking systems" if your locking system needs other
types of control signals.
Blue = input of +12V signal from the ignition key. This wire should be connected to the ignition key switch
(terminal 15). This signal will prevent an accidental locking while driving and resets the re-lock function (if
used). If you connect the blue wire to the GND, the accidental locking protection will be canceled.
White = door switch input (negative triggered). This signal controls the re-lock function. We recommend
door switches be installed to all doors of your car when you use the re-lock function. This function is
optional. Connect the white wire to the GND to disable the re-lock function.
Black = GND Supply. Connect this wire to the original GND point in the car.
Red = Positive Supply (the wire with a fuse 15A). It should be connected directly to the positive terminal of
the battery cable.
2x Violet = turn indicator (blinkers) outputs - these two wires provide power for the left and right blinkers
as a visual indication of locking, unlocking and trunk (5. door) releasing. Connect one of the violet wires
to the left blinker and the other violet wire to the right blinker.
The trunk (5th door) release output provides a positive voltage pulse (+12V, max. 15A), for a duration
of 0.5 seconds. This signal is suitable for an actuator with mechanical return to starting position. The
connecting wire is a part of the actuator. Plug the end of actuator wire equipped with a connector pin in to
the empty slot of the CL-301SL wire-harness connector (position 9) when you install the releasing device.
Note: The wire coming directly from the CL-301SL unit is the remote control antenna. The location of this
wire will effect the remote control working distance. Ideally, the wire should be near a window.
Operation: Each pressing of remote control button A (1) will lock or unlock the car (according to the
initial possition of the locks). If both buttons A (1) and B (2) are pressed, the trunk (5th door) will be
released (door locks will not be influenced). Locking of the car is indicated by one flash of the blinkers.
Unlocking is indicated by two flashes and trunk (5th door) releasing is indicated by three flashes. Doors
can not be locked with remote control while the ignition key is ON.
Re-lock function: If the car is not entered (neither door switch nor ignition key input is triggered) within
one minute after unlocking, the CL-301SL will automatically generate a lock instruction. (Connecting the
white wire to the GND instead of to the door switches will disable this function)
Confirmation of Control Code Validity: If the receiver unit receives an invalid signal from remote
control (for example: if there was an attempt to scan the code by a car thief, or, while rare, as may happen
after the remote control battery has been disconnected for a long time) then the receiver will not respond
to the signal from the remote control. In this case, the system will ask for a confirmation of the control
code. To provide confirmation, open the car by the key, put ignition key to On position and press any
button on the remote control. Now the remote controller should work as usual.
Maintenance: There is no special maintenance required. If the distance from your car at which the
locking system can be operated decreases, then replace the remote control battery. Normal life time of a
good quality battery should be about one year. A suitable replacement battery is BAT6.
Adding of a new remote control: There are two remote controls in each CL-301SL set. The
receiver unit can be operated with a maximum of three remote controls. To add an additional remote
control or to replace an original one (in the case one is lost) perform the following procedure.
Entering of Learn Mode: First, switch off ignition key and disconnect the power to the CL-301SL by
removing the fuse. Then, open the control unit housing. Press and hold the button marked "Learn Code"
inside the unit and reconnect the power while still holding down the button. The blinkers will flash four
times and you can now release the button. Now the receiver unit is in learning mode, ready to learn new
codes or to program output pulse duration.
Remote control codes learning: You should activate all the remote controls one by one (button A (1))
which you want accepted by the receiver when CL-301SL is in learn mode. The receiver unit will store
each remote control code in its memory (confirmed by a blinker flash). Keep in mind that only three
controls can be taught. If you try to teach a fourth control, the first one will be forgotten and so on. If you
activate only one control in learning mode, you will be able to control the car only with this one controller.
Duration of output pulses programming: Switch the ignition key to the ON position when the CL-301SL
is in the learning mode. Now use one of the remote controls, which is accepted by the receiver, to
program. Each short pressing of the remote control button will change the duration of the CL-301SL
output pulses. Topical duration is indicated by the blinkers. When the desired duration is programmed,
switch off the ignition key. The 60 sec. locking pulse can be used for powered windows control.
Number of
flashes
lock pulse open pulse
1 0.3s 0.3s
2 4s 4s
3 60s 0.3s
4 60s 4s
To exit the learning mode, disconnect the CL-301SL power for two minutes.
Note: All the settings and codes are stored in non voltage memory, so the receiver unit will remember
them even if the power is disconnected. Duration of trunk (5th door) release output pulse is fixed (0.5
sec.).
Examples of the CL-301SL use for different central locking systems: If your
locking system needs another kind of control signal, install a couple of over-switching relays (or CR-2S
unit) to the CL-301SL outputs. The relay coils consumption must be under 200 mA. See following
diagrams for different locking systems.
System with positive control inputs:
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CL-301 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CL-301 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info