555044
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Baby monitor BM-01A “Nanny“ 2/4 MFV51303 Baby monitor BM-01A “Nanny“ 3/4 MFV51303
Installation
1. Place the sensor pad on the bed bottom as shown in the diagram. Place
the mattress on the sensor pad and be sure that the sensor is well positioned
with the mattress using the following guidelines:
Center of the sensor pad should be approximately in the position of where the
baby’s chest will be
Pad should be on a smooth & solid surface – It should not be bent!!.
If there is only a spring grid supporting the bed, place a solid board (wood,
plywood etc.) between the pad and the spring grid.
If you want to use the Nanny in multiple beds, use extra sensor pads (item number
BM-01D). Install them in each bed and change only the location of the control unit.
Up to two sensor pads can be used in each bed with a single control unit if the
child is large.
2.
Connecting batteries to the control unit (battery compartment is on the rear
side of the control unit):
Use only 2 new size AA alkaline batteries.
Polarity of the batteries is clearly marked in the battery compartment.
Close the battery cover and turn the switch to position I.
If the batteries are OK, you will hear a beep and the indicators will flash.
Switch the unit OFF again (position 0)
If there is no beep after turning ON, check the batteries.
3.
Attaching the control unit to the bed – using the fastening belt
The unit should be visible and should not by covered by anything
For bigger children we recommend to locate the unit out of their reach
4. Connecting the sensor’s cable to the unit – you should hear a click
Route the cable in such a way that there is no slack long enough to make a loop.
For bigger children the cable should be out of their reach
If you do not use the entire length of the cable, fix the excess firmly under the
mattress.
If you position the control unit in another room, use the extension cable (5m),
which is provided with the set. Only one extension cable can be used.
If you use two sensor pads in a bed, a cable splitter is provided in the set.
To disconnect the cable from the unit – press the connector tab towards the cable
Switch and Indicators
Switch – position 0 = OFF, I = ON
Red indicator – flashing when there is an ALARM
Green indicator – a short flash indicates a breath or a movement of the baby
Yellow indicator – flashing indicates low batteries
Operation
A. Put the baby to bed.
B. Turn on the unit (confirmed by a beep and a flash of all LED indicators)
C. The green led indicator will flashes as the baby breathes or moves
D. Turn off the unit before you take the baby out of the bed.
ALARM
If the baby is not breathing for longer than 20 seconds, or the breath rate is too slow, an
alarm signal will sound and the red indicator will flash.
Check the baby and provide first aid if necessary
(make sure that there are no reasons
for choking, start resuscitation, call for emergency help). In some cases of Apnea the sound of
the unit itself can wake the baby up and he/she will start to breath again on his/her own.
Alarm can be stopped by the switching the unit off.
There may be rare cases of false alarms, especially when the child is crawling and moves
off the sensor pad.
Testing
You can test function of the Nanny in the following way (should be tested once a week):
1. If the baby is in the bed and the unit is ON, the green indicator should flash as the
baby is breathing or moving.
2. Leave the unit ON and take the baby out of the bed.
The green indicator may continue to blink for a certain time (vibrations of
the bed caused by the baby’s removal)
Do not hold or touch the bed – the device may detect your breathing
3. When the flashing has stopped for 20 seconds, the unit will make warning beeps and will
start the alarm sound
The red indicator should flash when the alarm is triggered.
Stop alarm by turning the switch on the unit OFF.
If the device does not work as described above, check that:
There is a beep after switching it on. If not, check the batteries.
After taking the baby out of the bed the green indicator stops flashing (within a
minute or so) – if not, the device is detecting some intrusive vibrations – see
following warning.
Important warning:
The Nanny is a very sensitive instrument, capable of sensing a sleeping baby’s
breathing. Intrusive vibrations of the bed, the floor or the entire building can influence
its performance. The bed should not be in physical contact with another bed (which
is used by another person or animal) or with any device that generates vibrations.
Intrusive vibrations can also be caused by a powerful air movement (fan, air-
conditioning…), by walking close the bed and by other sources. If you move the bed
to a new location, you should test the Nanny before you use it.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron BM-01 Nanny bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron BM-01 Nanny in de taal/talen: Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info