554863
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
The AC-83 wireless output relay module 2 / 2 MJT51401
Primary device Control device
Enrollment
method
Notes
Control panel PG
output
Enter 299 in
Service mode
Allows for heating mode switching (temperature regulation/antifreeze).
Not recommended for use in combination with other remote controls.
Remote control Press any button
Allows for heating mode switching (temperature regulation/antifreeze) via a remote control.
Thermostat
Magnetic door-
detector
Connect the battery
When triggered (a door/window is opened), the heating mode switches to antifreeze.
Wireless devices enrolled together with a thermostat to a single
relay can be used to determine how that relay reacts to signals from
the wireless thermostat. If desired, the relay can react only to the
freezing protection signal from the thermostat to turn on the heating
when the temperature gets below about +6C, or alternatively it can
react to the thermostat signal which demands heating when the
room temperature is lower than that pre-programmed in the
thermostat. The relay can be switched between these two modes
by operating the wireless devices.
The thermostat repeats its signal every 9 minutes, so if the AC-83
power is turned off for a while, and then on again, the relay will
synchronize with the thermostat within 9 minutes.
Use with a JA-8x OASiS control panel
Using an OASiS control panel with a thermostat in a combination is
only possible with the thermostat enrolled before the control panel. PG
outputs should be programmed in the control panel to have an
ON/OFF function. The PGX output can only be enrolled to the X relay,
and PGY to the Y relay.
If the control panel is enrolled to the X relay (by entering 299)
then the X relay is switched on whenever the corresponding
thermostat is activated and the control panel’s PGX output is active.
If the control panel is enrolled to the Y relay (by entering 299)
then the Y relay is switched on whenever the corresponding
thermostat is activated and the control panel’s PGY output is active.
Only one control panel PG output can be enrolled to each relay.
The control panel PG output allows the switch between temperature
regulation/antifreeze modes to be controlled either by the system
keypad or remotely via a mobile phone or the Internet.
Avoid enrolling key fobs to the same relay to which thermostat(s) and
PG outputs are enrolled as the control panel repeats currently valid PG
signals every 9 minutes. (The signals from the control panel would
override signals from the controller.)
Though the control panel’s requests to switch the heating mode
are recognized instantly, the relay will not react until a
subsequent thermostat signal is received (within 9 minutes).
Use with JA-80M (JA-82M) magnetic door-detectors
Heating mode switchover by thermostat can be overridden by a
JA-80M or JA-82M magnetic door-detector signal (or also signals from
a JA-80D universal transmitter). If such a detector is used, then
triggering the detector switches the heating to antifreeze mode, and
de-triggering the detector switches to regulation mode (regulating the
heating to a pre-programmed temperature).
Though the JA-80M/JA-82M requests to switch the heating mode are
recognized instantly, the relay will not react until a subsequent
thermostat signal is received (within 9 minutes).
When used in combination with an OASiS control panel, magnetic
door-detector activation status is of higher priority: At least one of the
detectors being triggered enforces antifreeze mode regardless of PG
output signals.
Magnetic door-detectors cannot be used in combination with remote
controls.
Use with RC-8x remote controls
You can switch heating modes via a remote control. Pressing the
(or
) button switches the relay to regulating the heating to the
(comfortable) pre-programmed temperature, pressing
(or )
switches the relay to regulating the heating to the anti-freeze
temperature.
Though the RC-8x requests to switch the heating mode are
recognized instantly, the relay will not react until a subsequent
thermostat signal is received (within 9 minutes).
Using remote controls for switching between heating modes
cannot be combined with control panel use or with magnetic-door
detectors.
Resetting the AC-83 unit
As a factory default, the AC-83 is supplied with nothing enrolled. To
reset a particular relay, do the following:
Repeatedly press the X button (or the Y button for the Y relay) to
achieve several LED flashes.
Then, continuously press the same button and keep pressing it (for
approx. 4 seconds) until all the LEDs flash a couple of times (=
reset). Then release the button.
Technical specification
Power supply 230V/50Hz, class protection II
Consumption about 1W
Relay contact rating
resistive load max. 2,5A / 250V AC
inductive (capacitive), lamp load max. 0,5A / 250V AC
Required fuse rating max. 5A
Communication band 868 MHz, Oasis protocol
Device enrollment is stored in non-volatile memory –
unaffected by power disconnection
Minimum distance from transmitting devices 1 meter
Operating environment general, indoor –10 to +40 °C
Enclosure IP40 EN 60529
Mechanical immunity IK08 EN 50102
Can be operated according to ERC REC 70-03
Complies with ETSI EN 300220, EN 50130-4, EN 55022,
EN 60950-1
Jablotron Ltd. hereby declares that the AC-83 is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC. The original of
the conformity assessment can be found on the web site
www.jablotron.com, Technical Support section.
Note
: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the manufacturer after use.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron AC-83 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron AC-83 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info