554822
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
AC-8014/814 receiver 2 / 2 MJQ51505
Enrollment of thermostats
For each channel of the receiver, a thermostat can be enrolled in the
following way:
Repeatedly press button < or > (left, right arrow) to select the
desired channel (the current channel will be indicated by its LED
flashing).
Insert batteries into the thermostat. When powered up, the
thermostat generates an enrollment signal and its code is stored in
the selected receiver channel’s memory.
Digital bus thermostats can be enrolled by pressing and holding
their button for 5 seconds.
Enrollment of a thermostat is confirmed by the constant lighting of
the green LED.
Only one thermostat can be enrolled to each channel. A thermostat
can be enrolled to multiple channels or other receivers without any
restrictions (it allows the control of several zones by one thermostat). If
you try to enroll a new thermostat to an occupied channel, the new
thermostat will be stored and the former one will be deleted.
Note: Enrollment codes are stored in non-volatile memory, so power
disconnection will not erase them.
Deleting a thermostat
To delete an existing thermostat:
Using buttons < and > select the desired channel (the current
channel will be indicated by its LED flashing)
Press the RES button, the corresponding LED will turn off and the
thermostat is deleted.
Indicators 1–14
Indicators on the front housing of the receiver indicate the status of
the output channels.
LEDs 1 to 14 Meaning
Off Channel is not used (no thermostat is enrolled)
Steady Green Channel has a thermostat enrolled, relay is off
Steady Red Relay is on (activated by the enrolled thermostat)
Flashing Green Communication with the enrolled thermostat is down
(Low battery in thermostat, radio interference etc.)
Flashing Red Enrollment mode (to enroll a thermostat)
Flashing Red
(rapidly)
Output is overloaded or short-circuited.
Using the MODE channel / SUM input
The receiver has a special MODE channel to which a JA-8x control
panel (PgX output) or RC-8x remote controls can be enrolled as well
as detectors of type JA-80M. The SUM terminal has the same function
for wired control. This channel can be used for remotely controlling the
mode in which all the outputs will work, switching between two
possibilities: 1) The outputs may be controlled by thermostat signals
demanding/stopping heating 2) The outputs are disabled, but will
respond to freezing alert signals demanding heating. The status of this
channel is shown by the MODE indicator.
Repeatedly press button < or > (left, right arrow) to select the MODE
channel (the current channel will be indicated by its LED flashing, in
this case aim for the MODE LED) and transmit the enrollment signal.
Enrollment of the transmitter is confirmed by the constant lighting of
the green MODE LED.
If no transmitter is enrolled to the MODE channel, then outputs 1-14
react in a normal way to signals from their corresponding thermostats.
If a control panel is enrolled and the PgX output is activated (MODE
indicator lit red) outputs 1–14 react in a normal way to signals from
their corresponding thermostats.
If the PgX output is deactivated (MODE indicator lit green), then
outputs 1–14 are deactivated. They can only be activated in response
to economy temperature signals from a TP-8x thermostat.
MODE indicator
Off
The MODE channel is not used – no transmitter is
enrolled (receiver reacts to standard signals from
thermostats)
Steady
Green
A transmitter is enrolled – the MODE channel is
deactivated, (SUM is active)
Outputs 1–14 only react to the economy temperature
signals from thermostats
Steady Red
A transmitter is enrolled – the MODE channel is
activated
Outputs 1–14 react to standard signals from
thermostats
Flashing
Green
Communication with the enrolled transmitter is down
(Low battery in transmitter, radio interference etc.)
Use and maintenance
All enrolled transmitters (thermostats and detectors) transmit regular
check signals. If the receiver does not receive the signal of an enrolled
transmitter for a certain period, it will indicate that communication with
this device is down (flashing green LED) and the corresponding output
will turn the heating on for 5 minutes every single hour.
One reason for the lost connection can be low batteries in the
transmitter. The average lifetime of a thermostat’s batteries is about
1 year (JA-8x detectors 3 years). Each transmitter checks its battery
conditions and signals in advance if the batteries are reaching a
critically low state (see the transmitter manual for details).
Another reason for possible connection failure can be radio signal
interference in the operational band of the receiver. In such a case the
receiver will usually indicate loss of communication with a multiple
number of transmitters. In this situation, check if there is any non-
approved or faulty radio-communicating device within the range of the
receiver.
If outputs 1–14 have not been activated for 7 days they will switch on
for 5 minutes to protect connected devices. This is also valid for the
output relay provided by the built-in AC-8000R module thus providing
protection for pumps which can be damaged if they are not used for a
long time. However, this feature is disabled for the boiler connection
established by an additional AC-8000R module.
Warning: the manufacturer is not responsible for any damage caused
by improper installation or any non-suitable use of this product.
Specifications
Power supply: 230 V AC, 50Hz, protection class II
Consumption: 0.02 A stand-by; 0.2 A max.
Max. power supply load 1.7A
Internal load-protection safety fuse F 3.15 A
Max. relay output load: 10 A / 230V
Voltage of outputs 1–14 and COM: 24V DC
Max. load of outputs 1–14: max. 0.4 A per single output
and 1.7A total for all outputs
Radio frequency: 868 MHz
Communication range 100 m (open area)
Dimensions: 258 x 214 x 77 mm
Mechanical resistance: IK08 according to EN 50102
Radio characteristics: ETSI EN 300220
EMC: EN 50130-4, EN 55022
Safety: EN 60950
Enclosure: IP30 (EN 60529)
Operational temperature: -10 to +40
o
C
Can be operated according to ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the
AC-8014/AC-814 is in compliance with the essential
requirements and other relevant provisions of Directive
1999/5/EC. The original of the conformity assessment can
be found on the web site www.jablotron.com
, Technical
Support section.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the manufacturer after use.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron AC-8014 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron AC-8014 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info